An asymmetric V-shaped bar ABC is attached to a surface at point A as shown below. The sides of the bar have the following lengths: AB = 160 mm, and BC = 200 mm. A force F = 500 N is applied at point C. The force vector is perpendicular to the side BC and points in the 4th quadrant assuming the standard orientation of the Cartesian xy-plane (with positive x-axis pointing right and positive y-axis pointing up). The bar and all forces are in the plane of the page (2D case). a) Calculate the moment of the force F about A point A. b) Calculate the moment of the force F about point B. c) Draw FBD of the bar ABC. Assume that the bar is weightless and supported by a smooth pin at point A. 160 mm F = 500 N 30° В 200 mm Attention: Convert millimeters to meters and uonort

An asymmetric V-shaped bar ABC is attached to a surface at point A as shown below. The sides of the bar have the following lengths: AB = 160 mm, and BC = 200 mm. A force F = 500 N is applied at point C. The force vector is perpendicular to the side BC and points in the 4th quadrant assuming the standard orientation of the Cartesian xy-plane (with positive x-axis pointing right and positive y-axis pointing up). The bar and all forces are in the plane of the page (2D case). a) Calculate the moment of the force F about A point A. b) Calculate the moment of the force F about point B. c) Draw FBD of the bar ABC. Assume that the bar is weightless and supported by a smooth pin at point A. 160 mm F = 500 N 30° В 200 mm Attention: Convert millimeters to meters and uonort

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the bar in the figure, with an quadrangular cross section, determine the maximum shear stress and angle of twist (in degrees) of one tip of the bar with respect to the other. The bar is made of steel with a modulas of rigidity of 79.3 Gpa. Moment at A is 100 N.m with the direction shown. Moment at B is 30 N.m, Moment at C is 70 N.m. L1 is 1.25m and L2 is 0.75m. The side cross section is 30 mm
force P in the xy-plane acts on the triangular plate. Determine P in the following situations:a) Find the moment of P if MO = 200 N · m clockwise, MA = 0, and MB =0.b) Find the moment of P if MO = 80 N · m counterclockwise, MA = 200 N · m clockwise, and MB = 0.
The structure of the figure is composed of components DABC, HEB and GDEF that are connected by pins at B, D and E. There are also two loads at C and F. Determine the forces acting on points B and D.H = 83
Charges q1, q2 and q3 are arranged in the x-axis. Charge q3 = 14 nC and is at the origin. Charge q2 = 4.5 nC and is at x = 2 cm. Charge q1 is at x =4. Solve for q1 (magnitude and sign) if the net force on q3 is zero. Express your answer in nC.
9 Consider the plane truss with load Pas shown in the figure. Let the horizontal and vertical reactions at the joint B be Hg and V, respectively and Vc be vertical reaction at the joint C. 2 exhoM S SLO 60° - II B A 60° D L 60° F 60° KLA G P с Which one of the following sets gives the correct values of VB, HB and V? (a) VB = 0; HB = 0; Vc = P (b) VB P/2; HB = 0; Vc = P/2 (c) VB = P/2; HB = P (sin60°); Vc = P/2 (d) VB = P; HB = P (cos(60°); Vc = 0 [2016
Q1. the resultant's line of action intersects member AB, measured from point B. Also show the force on the figure. See Figure shown below. Replace the force system acting on the frame by an equivalent force and specify where 35 lb 30° 20 lb 4 ft |A В 2 ft 3 ft 25 lb 2 ft C
Both elements have the same section and are made of the same material. Draw the shear and moment diagrams and draw the deformed Using matrix analysis techniques Realize the structural analysis (estimate forces in the supports and displacements in the free nodes) EI = 100.000 kn-m² I 10 m² H 12 m 20 N-m 目 8 40 kN 240 kw-m 2 12 m A
The structure in the figure is composed of two rigid bars (AB and CD) and two vertical rods made of aluminum and steel. All connections are pin joints. Determine the maximum force P that can be applied to the structure if the vertical displacement of its point of application is limited to 4 mm. Neglect the weights of the members. Answer must be in kN. For Aluminum: A = 454 mm² and E = 69 GPa, for steel: A= 358 mm2 andE 206 GPa. Alumimum 3m 3m 4m 4m
The structure in the figure is composed of two rigid bars (AB and CD) and two vertical rods made of aluminum and steel. All connections are pin joints. Determine the maximum force P that can be applied to the structure if the vertical displacement of its point of application is limited to 6 mm. Neglect the weights of the members. Aluminum 2 m A = 300 mm2 E = 70 GPa || A В Steel A = 500 mm2 E = 200 GPa 2 m 3 m 3 m C
The cross-sectional dimensions of a beam are shown. Assume bf=3.375 in., tf=tw=0.3125 in. and d=3 in.(a) If the bending stress at point K is 2050 psi (T), determine the internal bending moment Mz acting about the z centroidal axis of the beam.(b) Determine the bending stress σH at point H (positive if tension, negative if compression).
When force 2P is applied to the rigid arm ABC, point B displaces vertically downward through a distance of 0.5mm. Determine the normal strain developed in CD. A 500 mm- 300 mm B D 2P 400mm
The bending moment diagram is constant for an interval of a beam then the crossponding shear force diagram is an inclined straight line. A curved line. A line parallel to the axis. A zero line