An assembly made of a rigid arm A-B-C at end A and supported by an elastic rope C-D at end C is shown in the figure. The members may be assumed to be weightless and the lengths of the respective members are as shown in the figure. A Rigid arm Rope L Under the action of a concentrated load P at C as shown, the magnitude of tension developed in the rope is

An assembly made of a rigid arm A-B-C at end A and supported by an elastic rope C-D at end C is shown in the figure. The members may be assumed to be weightless and the lengths of the respective members are as shown in the figure. A Rigid arm Rope L Under the action of a concentrated load P at C as shown, the magnitude of tension developed in the rope is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 5 Rigid bar ABCD shown in the figure is supported by a smooth pin at D and by vertical aluminum alloy [E = 10,000 ksi] bars attached at joints A and C. Bar (2) was intended to have a length of 60 in.; however, its actual length after fabrication was found to be L2= 59.88 in. To connect it to the pin at C on the rigid bar, bar (2) will need to be manually stretched by A = 0.12 in. After bar (2) has been stretched and connected to the pin at C. Use the following additional properties and dimensions: A1 = A2 = 0.75 in², Determine: (a) the normal stresses in bars (1) and (2). (b) the deflection at A of the rigid bar. (1) 40 in 36 in Rigid bar 54 in P-20kips (2) L₂ 48 in D
The rigid bar of negligible weight is supported as shown in the figure. If W = 104 kN, compute thetemperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data:
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a= 2.9 x 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 x 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 31 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft O 3.74 kips 4.77 kips (1) B 3 ft 8 ft 1.5 ft 2 D
The two shafts are made of A-36 steel. Each has a diameter of 21 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B. They are also supported by journal bearings at C and D, which allow free rotation of the shafts along their axes. A torque of 500 Nm is applied to the gear at E as shown in the figure below. The shear modulus of elasticity for A-36 steel is 75 GPa. (Figure 1) Figure 50 mm 100 mm 1.5 m B 1 of 1 0.75 m 500 N-m Part A Determine the rotation of the gear at E. Express your answer using three significant figures. OF AΣo↓ vec PE=0.02897 Submit Previous Answers Request Answer Provide Feedback X Incorrect; Try Again; 8 attempts remaining ? rad
•Draw the Free body diagram •Solve step by step •Use 3 decimal places!
The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the 2 temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data: A (in) a (PF) E (GPa) Steel Rod 300 11.7 x 104 200 Bronze Rod 1400 18 x 106 83 Bronze 3 m Steel 1.5 m 1.0 m 2.5 m 1.5 m W
In the metallic structure represented by the figure below, the load P is 1200No. What is the maximum bending moment in member BC?
A tapered bar with varying diameter 1.5 d to d is subjected to tensile force of magnitude 1000 N. The Young's modulus of elasticity of the material is E = 160 GPa, length of bar 1 = 2 m, d = 20 mm. The extension caused by tensile load. A 0.026 mm B 0.039 mm C 0.052 mm D 0.043 mm
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 97 GPa] with a cross-sectional area of A₁ = 220 mm². Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 550 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1620 mm, a = 1120 mm, b = 680 mm, c = 500 mm, and L₂ = 1200 mm. If a load of P = 112 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. 4 (1) L a A b (2) D L2
In the figure, the ac element is rigid and is held with the bars AB, CD and EF, each of which has a cross-section of 145 mm ^ 2, without a blank and without tension. The AB bar can be changed with a screw mechanism over 0.75. The step of the screw in a full turn is 1.5 mm. If the screw is rotated 1.5 steps in the direction of shortening the length of the EF rod, what is the value of the force that will occur on the EF rod? Take the elastise modulus 210 GPa for all bars
Q:A rigid block of negligible mass is supported by three rods as shown in figure, if a load (P) is subjected to the block, find the stress in the steel and aluminum rods. The area in addition to the properties of each material are given in Table below: E, Ea A, Aal A(mm) (mm) (Gpa) (Gpa) (mm') (mm') (kN) (Gра) 500 0.1 190 80 800 1600 1200 Steel Steel
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a = 2.9 x 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 x 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 38 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft 5.16 kips 4.86 kips 2.48 kips 3.88 kips O 4.09 kips (1) B 3 ft P 8 ft 1.5 ft