An aqueous slurry containing 1.5 lbm of solid per gallon of liquid is pumped through a filter cloth by a centrifugal pump. If the pump provides a constant pressure drop of 150 psig, how long will it take for the filter cake to build up to a thickness of 2 in.? The density of the filter cake is 30 lbm/ft^3 , and its permeability is 0.01 Darcy

Q: Consider a 1000 m^2 impoundment, 1 m deep. Benzene is present at 100 micrograms/L when the wind…

A: Given that, Area of impoundment, A=1000 m2  Depth, h=1 m Speed of wind over surface, u=2 m/s…

Q: 19.16 A 0.2-m-wide plate, 0.8 m long, is placed on the bottom of a shallow tank. The plate is…

A:

Q: 4B. A fluid is streaming over a flat surface maintained at a different temperature. Measurements of…

A: The correct answer is to be identified.

Q: (a) Air at 1 atm (abs) is flowing through a tube having an inside diameter of 50 mm at a velocity of…

A: Given a) Ait at P=1atm Tube D=50mm T=350K V=15m/s Find Heat transfer coefficient, h Effect of…

Q: Air at 1 atm and 400 K and with a velocity of U∞o = 10 m/s flows across a compact heat exchanger…

A:

Q: Below is shown the results for a series of cake filtration experiments on two types of waste sludges…

A: Correct. The higher slope (1.27) for Type B implies a greater increase in specific cake resistance…

Q: Determine the resistance in each scenario presented. Explain whether the resistance is linear or…

A: To find:a) whether the flow is laminar and the resistance.b) Pump resistance from the pump curve.c)…

Q: pipe, g/cm', and the melt has a dynamic viscosity of 3.12 g

A: 1. diameter= 10cm = 10*10-2m 2. Density = 7.8 g/cm3= 7800 kg/m3 3. dynamic viscosity= 3.12g/ms=…

Q: 3 A constant-density Newtonian fluid is flowing as a thin film down a vertical wall in laminar flow;…

A: Newtonian fluid flowing as a thin film down a vertical wall in laminar flow.

Q: 2. 6 The diameter of a cylindrical core sample is 2. 5 cm, its length is 6. 0 cm. Under a pressure…

A: Given data: Diameter of cylindrical core = 2.5 cm Length of core = 6 cm Pressure difference = 0.3…

Q: (а) Build the four II groups for this problem (let p, µ, and D be the wilds). (b) What is the ratio…

A: (A) Vc = f ( D, dP, g, ρf, μ, ρP) There are 7 variables Vc, D, dP, g, ρf, μ, ρP There are 3…

Q: (a) Is flow in the boundary layer laminar or turbulent at the end of the plate, L = 2 m? (b)…

A: To tell the boundary layer laminar or turbulent we use a dimensionless number called Reynolds Number…

Q: After pressure spraying, there is a thin layer of water (at 70°F) left inside of a 24 inch diameter…

A:

Q: Ex) Air at 0 C and 1 atm flows at a velocity of 6 m/s across a rectangular plate at a uniform…

A:

Q: Problem 2 A toy manufacturer wishes to extend the time that a spherical rubber ball will stay…

A:

Q: 17.17. The fins on the radiator of your car are about 2 in long. When your car is going 60 mi/h, the…

A: length of fin x=2 inchvelocity approaching the fins  v=40 mi/hr = 17.88 m/s

Q: a. Find the velocity distribution and the volumetric flow rate per unit width of wall by using the…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: 3. What factors should we take into account for the selection of the pipe size and design of the…

A: 1. Material: Pipe material assumes a vital part in deciding the quality and tension of compacted…

Q: A centrifuge with a bowl which is 500 mm long and has an inside radius of 50.5 mm is to be used to…

A: Given : Bowl length Bowl radius Rotation speed Liquid depth Crystal diameter

Q: A company producing detergents uses industrial minerals such as phosphate salts and silica in their…

A: Given: diameter of the clay particles=50 μm=5*10-6difference between the densjties(ρp-ρL)=2400…

Q: calculate the gauge pressure at the bottom

A: