An analog Electromyogram (EMG) signal contains useful frequencies up to 3000 Hz. i. Determine the minimum required sampling rate to avoid aliasing. ii. Suppose that we sample this signal at a rate of 6500 samples/s. what is the highest frequency that can be represented uniquely at this sampling rate?

An analog Electromyogram (EMG) signal contains useful frequencies up to 3000 Hz. i. Determine the minimum required sampling rate to avoid aliasing. ii. Suppose that we sample this signal at a rate of 6500 samples/s. what is the highest frequency that can be represented uniquely at this sampling rate?

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.3: Signal System

Problem 1R

See similar textbooks

Similar questions

(b) Consider a voice signal from a analog telephone which needs to be digitized. Explain the steps involved in the conversion of analog to digital signal. If suppose the sampled analog values are 1V, 2V, 3.5V and 4.5V, use a 2 bit quantizer to digitize these values. Assume the range of sampled analog values from 0V to 5V. Provide the digitized values of this signal and draw the digital signal.
1.) Determine the bit rate and quantization step of the ADC in the sampling of analog signal with x[n] of 1.02 Vpp, sampling rate of 20 samples per second, and 8-bit binary code 2.) An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 6MHz. The quantization error in any one sample value must be within (plus-minus sign) 0.5% of the peak-to-peak amplitude range of the ADC. How many binary digits must each sample contain?
MCQ) 5)Quantization error------: a. decreases as the bits per sample increases b. decreases as the bits per sample decreases c. decreases as the sample rate increases d. decreases as the sample rate decreases 6)The difference between the actual value of the sample and the quantized value of the sample is called: a. PAM error b. Sampling error c. Quantization error d. PCM error ThESE multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer.
Q2/ The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ±0.1% (full scale). The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of -10 to +10 volts. Find the minimum sampling rate required. i) ii) Find minimum bit rate required in the PCM signal. Find the number of bits in each PCM word. iii) iv) Find the minimum absolute channel bandwidth required for the transmission of the PCM signal.
What is the value of the 8 digital bits that are represented as in the figure above if (Hint: the first bit is 1): a. The signal is encoded as NRZ-L: b. The signal is encoded as NRZ-I:
2/ Information in an analog waveform, whose maximum frequency is 10 kHz, will be transmitted using a minimum sampling rate and a 32-PAM system. transmitted using a minimum sampling frequency and a 32-PAM system. The quantization distortion shall not exceed 0.01% of the The quantization distortion must not exceed 0.01% of the peak-to-peak value of the analog signal. a/ What is the minimum PCM word size to be used in the system? b/ What is the baud rate?
1) Determine the bit rate and quantization step of the ADC in the sampling of analog signal with x[n] of 1.02 Vpp, sampling rate of 20 samples per second, and 8-bit binary code. 2) An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 6MHz. The quantization error in any one sample value must be within ± 0.5% of the peak-to- peak amplitude range of the ADC. How many binary digits must each sample contain?
2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?
Qَ\ discuss a conversion of an analogue signal to digital bits Please I need to resolve the question quickly
What is the minimum sampling rate needed in order to successfully capture frequencies up to 80MHz in an analog signal?
I would be very happy if you solve the question of this signal processing issue quickly.
b. Explain how to decide the sampling rate for a multi-frequency input signal. c. An ADC with word length of 24 bits. If the input analogue signal range is 3.7 V, what is the resolution of this ADC? d. Consider a thermocouple giving an output of 0.5 mVrc. What will be the word length required when its output passes through an ADC if temperatures from 0°C to 120°C are to be measured with resolution of 1.5°C?. Assume 12V as system voltage.