An amplifier has a voltage gain of 10, an input resistance of 1M ohm and an output resistance of 10. The amplifier is connected to a sensor that produces a voltage of 1V and has an output resistance of 1k, and to a load of 50,. What will be the output voltage of the amplifier (that is, the voltage across the load resistance) ? Source Amplifier Load R, = 1k) R= 10 2 R. 1MO R. 50 2 1V Select one: O a. VO = 1OV Ob. Vo=5.6 Oc. VO=8.3 Od. Vo = 9.3

An amplifier has a voltage gain of 10, an input resistance of 1M ohm and an output resistance of 10. The amplifier is connected to a sensor that produces a voltage of 1V and has an output resistance of 1k, and to a load of 50,. What will be the output voltage of the amplifier (that is, the voltage across the load resistance) ? Source Amplifier Load R, = 1k) R= 10 2 R. 1MO R. 50 2 1V Select one: O a. VO = 1OV Ob. Vo=5.6 Oc. VO=8.3 Od. Vo = 9.3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Which of these is incorrect for an operational amplifier? a) It has a high voltage gain b) It is a direct coupled amplifier c) It is only useful for amplifying AC signals d) It was originally designed to perform mathematical operations
5. If you have this relationship between the input and output voltage Vou=1.5 Vin+2 in which 2 is a bias. Design a circuit that will remove the bias and make the relationship between the input and output as Vou=1.5 Vin. We have a dual supply of ± 12 V available and we need to drive a 10 kQ load. Test your designs under different input voltages and verify that your output voltages are within + 5% of the calculated ones. Simulate the circuit in Multisim and then implement it practically. Prepare a full report about the experiment.
There are point loads ,Q1 = 5, Q2 = 8 and Q3 = 6 at points A(-8,0), O(0,0) and B (6,0) in the OXY plane, respectively.Write the value of the x-component of the electric field in ke numerically at the point P(0, 10) on the-axis.
What are the voltage gain, input resistance, andoutput resistance of the amplifier as shownif R1 = 12 k and R2 = 120 k ? (b) Repeat forR1 = 160 k and R2 = 330 k ? (c) Repeat forR1 = 4.3 k and R2 = 270 k ?
Sid nov
1. Which of these is incorrect for an operational amplifier? a) It has a high voltage gain b) It is a direct coupled amplifier c) It is only useful for amplifying AC signals d) It was originally designed to perform mathematical operations
A CC amplifier can be used when a. all of the above b. a current gain without a voltage gain is required c. a voltage gain and a current gain is required d. matching high to low impedances
Identify the types of power amplifiers used to amplify low-level AM signals. (Check all that apply.) Class C amplifier Class D amplifier Class A amplifier Class B amplifier Linear amplifier
What is the power gain of the amplifier circuit in the figure? For BJT: beta(F) = hFE = 100 beta(f) = hfe = 200 VBEQ = 0,6V VT = 25mV hre = hoe = 0
Find the desired in point 54 with finding what you can find.
Question-2: For the amplifier shown, determine: 1. Maximum value for the emitter bypass capacitor, C2, if the amplifier must operate over a frequency range from 200 Hz to 10 kHz. Vcc +10 V Boc-100 Bac=175 2. Voltage gain Ay. Re 4.7 kfl R C, 47 Vout 3. The DC collector voltage Vc. Vin 4. The Attenuation. R 47 kfN 5. The AC collector voltage Ve. R, 600 n R2 10 kN R 470 1 Vs 15 mv 470 1
Please solve with steps, using to study. Will upvote!