An aluminum rod is rigidly attached between bronze rod and steel rod as shown. Axial loads are applied as indicated. Find the maximum value of P that will not exceed a stress of steel of 120 Mpa , in aluminum of 95 MPa, or a bronze of 105 MPa, steel A = 600 mm aluminum bronze | 400 mm? 150 mm? ЗР 3P + .a) What is the maximum value of "P" that will not exceed the given stresses of the three metals. .b) Using the determined maximum value of "P" what will be the stress exerted by steel. .c) Using the determined maximum value of "P" what will be the stress exerted by aluminum. Using the determined maximum value of "P" what will be the stress exerted by bronze.

An aluminum rod is rigidly attached between bronze rod and steel rod as shown. Axial loads are applied as indicated. Find the maximum value of P that will not exceed a stress of steel of 120 Mpa , in aluminum of 95 MPa, or a bronze of 105 MPa, steel A = 600 mm aluminum bronze | 400 mm? 150 mm? ЗР 3P + .a) What is the maximum value of "P" that will not exceed the given stresses of the three metals. .b) Using the determined maximum value of "P" what will be the stress exerted by steel. .c) Using the determined maximum value of "P" what will be the stress exerted by aluminum. Using the determined maximum value of "P" what will be the stress exerted by bronze.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ (A) - The mechanism of femur bone is approximated as a circular tube (3 cm and 2 cm are the outer and inner diameter respectively) under loads as shown in figure Q1-A, determine the state of stresses at the points A and B. 40 cm 5 cm 380 N Figure Q1-A 300 N
The state of plane stress at a point on the surface of the airplane fuselage is represented by the stress element shown in the figure. Using Mohr's Circle, determine a) the principal stresses and the maximum in-plane shear stress specifying the orientation of the element in each case. b) The equivalent state of stress at the point on the element that is oriented {a} clockwise from this position Draw all the corresponding stress elements. Given x = {x} MPa; y = {y} MPa and xy = {xy} MPa xy MPa y y MPa 10000 x MPa →→→→x Solve in terms of variables
Problem 2.3 A machine bracket is loaded with an inclined force of 1000 N as shown in the figure 1000N 200mm -A- CHAPTER 250mm 1000N A 450 50mm a) Find the principal stresses at point A. b) Show the results on a properly oriented element.
MENG222 STRENGTH OF MATERIALS P=1000
140mm $50 mm 100 mm | I kN In the figure, a force of 1 kN is applied by means of an arm connected to a shaft with a diameter of 50 mm. So, represent the stress state of point B on the element? b) Draw the Mohr's circle for the given stress member and calculate the principal stresses?
QUESTION 12 The compound steel bar shown in Figure is made of three uniform segments marked as 1, 2 and 3 of diameters 30mm, 20mm and 10mm respectively and is loaded as shown. The stress in segment 1 is: 30mm 20 mm 10 mm 25kN 80 kN 2) 40 kN + 2m 1m 1m 臺 O a. 35.4 MNm2 O b. 92 MNm O c. 318.3 MNm2 С. O d. 113.2 MNm 2 QUESTION 13
The state of stress shown to the left was produced by a combination of loadings on a body that is not shown. Determine the following via Mohr's circle: A) Draw Mohr's Circle for the x-y plane. B) Determine the principal stresses - All 3. C) Sketch a properly oriented differential element showing the principal stresses in the x-y plane. D) Determine the magnitude of the maximum shear stress in the x-y plane. E) Sketch a properly oriented differential element showing the maximum shear stress state in the x-y plane. F) Determine the magnitude of the absolute maximum shear stress (and include the two out of plane circles on your original figure). Use the following values for the magnitudes of the stresses: x = 0₂ Txy Ox X X 10 ksi, σy = 4 ksi, σ₂ = 3 ksi, Txy = 4 ksi
oy =510 (kg/cm2) Plane Stress In the stress element given in Figure, WITH MOHR CIRCLE; a- Determine the principal stress directions by calculating the principal stress values a nd Show in the stress quadrilateral. T=330 (kg/cm2) b- Calculate the largest and smallest shear stresses and determine their directions. oy Determine it and represent it in a stress quadrilateral.
1. At a point in a piece of elastic material, direct stresses of 92 MN/m2 tensile and -49 MN/m2 compressive are applied on mutually perpendicular planes. The planes are also subjected to a shear stress. If the greater principal stress is limited to 100 MN/m2 tensile, determine the value of shear stress. Give you answer to 2 significant figures in MN/m2
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under tension. If the wire length extension is 2.5 mm, calculate the stress in the wire. Give your answer in N/m2to 2 decimal places. (show all work)
Please read the instructions carefully and do what are asks. Illustrate and show the COMPLETE SOLUTIONS. FN=70 MN=76 SN=50
Q2) For the state of plane stress given on the element below, construct a Mohr's circle. Use circle to determine (1) the principal stresses, (2) the principal stress direction, (3) the maximum in-plane shear stress and corresponding and normal stress. 100 MPa 150 MPa Tay - 50 MPa