An aluminum metal rod with thermalconductivity of 205 W/(m K) has a length of2 m and a cross sectional area of 0.1 m2.One end is connected to a hot reservoir at atemperature of 373 K while the other end isconnected to a cold reservoir at atemperature of 273 K. What is the Heatcurrent?989 W1200 W800 WO 1025 W

Given: K= 205 W/mK l= 2m A= 0.1 m2 TH= 373 K…

Answered: An aluminum metal rod with thermal…

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The resistivity of a metal increases slightly with increased temperature. This can be expressed as p=po [1+ a(T-To)], where To is a reference temperature, usually 20°C, and a is the temperature coefficient of resistivity. For copper, a=3.9x 10-3 °C-1. Suppose a long, thin copper wire has a resistance of 0.25 at 20°C. Part A At what temperature, in °C, will its resistance be 0.25 ? T= Submit 5 ΑΣΦ V Request Answer ? °C
An engineer is designing a wire using an unknown material that will carry large amounts of electricity. The resistive heating of a 54.62 g wire is expected to add 515 J of heat energy during a 22-minute operating cycle. What is the temperature increase of the wire? You may use the following information about the unknown material to answer the question: Specific Heat = 0.28 J g-1 °C-1 Density = 8.29 g/cm3 Coefficient Thermal Expansion = 9.7 µm m-1 K-1
An immersion heater utilizing 120 V is used to raise the temperature of a 100 g aluminum cup containing 350 g of ice from -20.0 ºC to a final temperature 35.0 ºC. How much energy is supplied by the immersion heater? cAl = 900 J/kg.ºC, cwater = 4190 J/kg.ºC, Lf,Al = 3.80 x105 J/kg, Lf,water = 3.34 x106J/kg, melting point Al = 660 ºC, boiling point water = 100 ºC, csteam= 2010 J/kg.ºC Clearly state the formulae you’re using and what your letters/symbols mean.
A 19 century lab technician is testing possible metals for bulb filaments. A tantalum filament with a surface area of 0.370 mm and an emissivity of 0.976 radiates 0.80 W of light. Determine the filament's temperature (in K). The melting point for tantalum is 3269 K.
Two pieces of copper with the same mass are melted to make A and B cables with radii r and 3r, respectively. Two cables are connected in series and current is passed through them. What is the ratio of the heat emitted by cable A to the heat emitted by cable B? A 1:9 B 81:1 D 9:1 1:81
A tungsten wire is used to determine the melting point of indium. The resistance of the tungsten wire is 2.221 at 20.0°C and increases to 4.307 as the indium starts to melt. αtungsten = 4.50 x 10−3 (°C)−1. What is the melting temperature of indium in °C?
A classroom has dimensions 8.00 m x 10.00 m x 3.00 m. A 1000 W electric space heater is being used to warm the room from 5.00°C to 20.00°C on a cold morning. If the density of air is 1.29 kg/m°, and the specific heat capacity of air is 1004 J/(kg-K), how long will it take to heat the room? Assume no loss of thermal energy to the surroundings. A) 1.30 minutes B) 241 minutes C) 45.3 minutes O D) 77.7 minutes
A small metal cube with a thermal mass mc and an initial temperature 0 is dropped into a container of water that is actively maintained at a constant temperature 0w. The cube quickly comes to rest on the bottom surface of the container. The bottom surface is maintained at a constant temperature 0 (note that this is different from 0w). The thermal resistance between the cube and the water is Rcw while the thermal resistance between the bottom surface of the container and the cube is RCB. The temperature of the cube is denoted by 0c. a) Draw the system schematic indicating the assumed directions of the heat transfer rates. Label all the nodes and system parameters. b) Derive the governing equation for the temperature of the cube, 0c. c) Where does to appear in the system schematic and how does it affect the governing equations? d) Calculate the steady-state temperature of the cube, css, assuming the following system parameters: 0o = 21°C, 0B = 6°C, 0w = 0°C, Rcw = 2°C/W, and RCB = 4°C/W
An engineer is designing a wire using an unknown material that will carry large amounts of electricity. The resistive heating of a 66.08 g wire is expected to add 529 J of heat energy during a 11-minute operating cycle. What is the temperature increase of the wire? You may use the following information about the unknown material to answer the question: Specific Heat = 0.232 J g-1 °C-1 Density = 7.36 g/cm3 Coefficient Thermal Expansion = 6.6 µm m-1 K-1
At 20°C, the carbon resistor in an electric circuit connected to a 6.0-V battery has a resistance of 2.6 x 102 n. what is the current in the circuit when the temperature of the carbon rises to 73°C?
Copper wire has a resistivity o = 1.7 x 10-8 22m when at 20°C and it has a temperature coefficient a = 3.9 × 10-3 K-1. A solid cylinder of copper of length L = 85 cm and diameter D = 1.5 mm has one end held at T₁ = 15°C and the other end is held at T2 = 230°C. The temperature increases linearly between the two ends of the cylinder. T₁ dx R= L T₂ Part (a) Consider a thin slice of the copper cylinder of thickness dx that is located a distance x from the left end of the cylinder. Write an equation for the temperature of this slice in terms of the variables x, L, T1, and T2. Part (b) Determine the total resistance in milliohms.
Physics v Q13 A current is passed through a resistor for some time. It produced 400 cal of heat in this period. If the current is doubled, how much heat will be produced in the same duration? 200 cal 400 cal 800 cal 1600 cal 00OO

SEE MORE QUESTIONS

Recommended textbooks for you

College Physics

Physics

ISBN:

9781305952300

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

University Physics (14th Edition)

Physics

ISBN:

9780133969290

Author:

Hugh D. Young, Roger A. Freedman

Publisher:

PEARSON

Introduction To Quantum Mechanics

Physics

ISBN:

9781107189638

Author:

Griffiths, David J., Schroeter, Darrell F.

Publisher:

Cambridge University Press

College Physics

Physics

ISBN:

9781305952300

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

University Physics (14th Edition)

Physics

ISBN:

9780133969290

Author:

Hugh D. Young, Roger A. Freedman

Publisher:

PEARSON

Introduction To Quantum Mechanics

Physics

ISBN:

9781107189638

Author:

Griffiths, David J., Schroeter, Darrell F.

Publisher:

Cambridge University Press

Physics for Scientists and Engineers

Physics

ISBN:

9781337553278

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Lecture- Tutorials for Introductory Astronomy

Physics

ISBN:

9780321820464

Author:

Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina Brissenden

Publisher:

Addison-Wesley

College Physics: A Strategic Approach (4th Editio…

Physics

ISBN:

9780134609034

Author:

Randall D. Knight (Professor Emeritus), Brian Jones, Stuart Field

Publisher:

PEARSON

SEE MORE TEXTBOOKS

An aluminum metal rod with thermal conductivity of 205 W/(m K) has a length of 2 m and a cross sectional area of 0.1 m². One end is connected to a hot reservoir at a temperature of 373 K while the other end is connected to a cold reservoir at a temperature of 273 K. What is the Heat current?