Answered: An aluminium wire and steel of the same… | bartleby

Related questions

Question

An aluminium wire and steel of the same
length & cuoss-section are joined end lo
end. The composite wire is hung from a rigid
suppout and a load is suspended from
free end. If the increase in the composite
wire és 2.4mum, find the increase in
the length of each wire.
is

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

the point that identifies the proportional limit of the material whosee graph of stress as a function of strain is shown as?
Two horizontal forces P are applied to pin B of the assembly shown. Knowing that a pin of 0.8-in. diameter is used at 0.5 in. each connection, determine the B maximum value of the average normal stress (a) in link AB, (b) in BC,(specify if the forces are tension or compression), (c) the average shearing stress in the pin at C, (d) the average bearing stress at C in member BC, (e) the average bearing stress at B in 18 in, link 0.5in A 60° 1.8 in. 45° member Bc. C Let P = 20 kips
The overhead hoist shown below is being designed to lift loads up to F = 12 kips. Your company requires a safety factor against buckling of SFbuckling = 4 and a safety factor against yielding of SFyielding = 5. Determine the minimum acceptable diameter of rod BD to the nearest in. Solid rod BD is made out of 2024-T4 aluminum, has a circular cross-sectional area, and is pinned at B and at D. The dimensions of the hoist structure are LAB = 5 ft; LBC = 6.5 ft, rp = 1 ft, and 0 = 25 º dmin Save & Grade Last attempt A D 0 LAB Save only B in LBC ? X0% Tp F Additional attempts available with new variants
A horizontal cable supports the boom of a crane. If the tension in the cable is4500 N and the crane is supporting a 7500-N girder, what is the compressionin the boom?
for the below figure, the rod of mass 50kg and length 6m is in the equilibrium. It is hinged to a wall at 0. The rod is at an angle of 40˚ above the horizontal and the rope makes an angle of 70˚ with the rod. (a)find the tension in the rope (b)find the force exerted by the hinge 0 on the rod.
An elastic with the elasticity constant of 20 N/m, and mass of 4 kg, is fastened to the ceiling and hanging down. Calculate the stress which occurs in it, if the cross-sectional area amounts 10 cm2.
A uniform 300 NN trapdoor in a ceiling is hinged at one side. Find the net upward force needed to begin to open it if the upward force is applied at the center. Express your answer with the appropriate units. Find the total force exerted on the door by the hinges if the upward force is applied at the center. Express your answer with the appropriate units Find the net upward force needed to begin to open it if the upward force is applied at the center of the edge opposite the hinges. Express your answer with the appropriate units. Find the total force exerted on the door by the hinges if the upward force is applied at the center of the edge opposite the hinges. Express your answer with the appropriate units.
a cable has a diameter of 4mm and an original length of 2m.The cable is pulled by a force of 130N.The final length of the cable is 2.02m -calculate the youngs modulus of the cable
A high-speed lifting mechanism supports a(n) 880-kg object with a steel cable that is 28.0 m long and 4.00 cm² in cross-sectional area. (a) Determine the elongation of the cable. (Enter your answer to at least two decimal places.) mm (b) By what additional amount does the cable increase in length if the object is accelerated upwards at a rate of 3.1 m/s²? mm (c) What is the greatest mass that can be accelerated upward at 3.1 m/s² if the stress in the cable is not to exceed the elastic limit of the cable, which is 2.2 x 10³ Pa? kg
A shearing force of 75 N is applied to an aluminum rod with a length of 10 m, a cross-sectional area of 1.0 x 10-5 m2, and a shear modulus of 25 x 109 N/m2. As a result the rod is sheared through a distance in mm of:
Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have, and specify where D must be located for a strut of this length to be used. Take x= 120 mm. 60 mm D. y 20 mm E The smallest length CD may have is mm. The coordinates of point Dare ( and Imm.
Ggg