An airplane tows a banner that is b = 0.9 m tall and l = 22.2 m long at a speed of 169 km/hr. (a) If the drag coefficient based on the area bl is CD = 0.06 estimate the power required to tow the banner. (b) Estimate the power required if the airplane was instead able to tow a rigid flat plate of the same size. (a) (b) i 76.2 6.35 kW kW

An airplane tows a banner that is b = 0.9 m tall and l = 22.2 m long at a speed of 169 km/hr. (a) If the drag coefficient based on the area bl is CD = 0.06 estimate the power required to tow the banner. (b) Estimate the power required if the airplane was instead able to tow a rigid flat plate of the same size. (a) (b) i 76.2 6.35 kW kW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The main cross-cable between towers of a coastal suspensionbridge is 60 cm in diameter and 90 m long. Estimatethe total drag force on this cable in crosswinds of 50 mi/h.Are these laminar flow conditions?
1. A sign is exposed to a 15 mph wind on a standard day. You may neglect the "legs" of the sign in all cases. Estimate the drag on the sign if (a) the sign is aligned lengthwise to the wind. (b) the sign is crosswise to the wind (wind perpendicular to the face of the sign). 3 m wind (part a) Tempe ASU Next Exit wind (part b) 1m 1m Configuration for part a. Configuration for part b. 1. (c) the sign is rotated by 90 degrees (so that it is 3 m high and 1 m wide) and the wind is parallel to the face of the sign. (d) the sign is rotated by 90 degrees (same orientation as in part c) and the sign is crosswise to the wind. 1m wind (part c) Tempe ASU 3 m Next Exit Configuration for part c.
An aeroplane has a rectangular planform wing with a span of 12 m and a chord of 2 m. The aircraft is flying at cruising speed of 62 m/s at an altitude of 3,200 m. Assume that the skin-friction drag on the wing can be approximated by the drag on a flat plate of the same dimensions at 0° incidence. Calculate the skin-friction drag and the maximum boundary layer thickness assuming (i) a completely laminar flow, and (ii) a completely turbulent flow. Assume μ = 1.63.10-5 N s/m², p = 0.89 kg/m³. Then, calculate the skin-friction drag accounting for transition at Recr= 5.105. What would the drag benefit be if transition was delayed to a Reynolds number of 106? What reduction in a propeller engine power would this imply in the cruise condition, assuming a propeller efficiency of 0.88?
Answer this ole
3) An advertising sign mounted on the roof of a car is 33 inches tall, 15 inches wide and 54 inches long (airflow direction). The underside of the sign is flush with the top surface of the roof. Take air properties to be: p = 0.075 lbm/ft' and u= 1.22x10 lbm/ft.sec. Used a pressure drag coefficient of 1.2 for the advertisement sign. Calculate the total drag on the sign and the power required to overcome its effect if the car is travelling at a constant speed of a) 12 mph and b) 45 mph. Note: Provide a schematic diagram (sketch) of the problem configuration (if applicable). Every numerical calculation must be preceded by the appropriate equation. Do not forget units & dimensions during your calculations.
b) When tested in water at 20°C flowing at 2_m'sAlan 8 cm diameter sphere has a measured drag force of 5 N. Determine the velacity and drag force ony l,5 n diåmeter weather balloon moored in sea-level standard air under dyhamidally 'similar conditions? For sea-level standard air, take p = 1.2255 kg/m² ànd u» 1.78 x 10-5kg/m·s
i need the answer quickly
A wing of 2 percent camber, 5-in chord, and 30-in span istested at a certain angle of attack in a wind tunnel with sealevelstandard air at 200 ft/s and is found to have lift of 30 lbfand drag of 1.5 lbf. Estimate from wing theory (a) the angle ofattack, (b) the minimum drag of the wing and the angle of attackat which it occurs, and (c) the maximum lift-to-drag ratio.
Parvin bhai
You are designing an airfoil for a new hobby RC plane. Because of your limited knowledge, you have mistakenly approximated your airfoil as an ellipse with a = 75mm and b = 12mm. Here, “a” is the depth of your wing and “b” is the thickness. Your plane travels through the air at approximately 20mph (8.9m/s). As it does so, skin friction produces a drag-induced heat of 800W on your wind, of length 1m. Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), TInfinity = 25oC a) What is the Reynold’s number? Hint: “D” is taken to be the thickness for an elliptical crosssection. b) What is the Nusselt number? c) What is the convection coefficient? d) What is the average temperature of your wing? Assume an ellipse perimeter of approximately 200mm.
An aircraft has the drag polar, C_d=0.015+0.05C_l^2 For a lift coefficient of 0.5, find the value of the drag coefficient and lift drag ratio? I am asking It For Second Time. Please Read the Question Carefully.
1 .Water at 15 ºC flows past a 1.5 mm radius small sphere at 5 cm/s. What is most nearly the drag force in kgf of the sphere, if the sphere has a drag coefficient of 0.47