An air-standard cycle consists of the following processes: isentropic compression from 15°C, 1.01 bar through a compression ratio of 5:1. heat addition at constant volume of 2600 kJ/kg. (i) (ii) reversible adiabatic expansion to the initial volume. heat rejection isochorically. (iii) (iv) For air take R = 0.287 kJ/(kg·K) and cp = 1.005 kJ/(kg·K). Sketch the cycle on P-v and T-s diagrams, and calculate its ideal efficiency, mean effective pressure and peak pres- sure. Take the start of isentropic compression as state point 1. Now the cycle above is modified in two ways so the heat is added, i.e., (a) isobarically, and (b) half isochorically and half isobarically. Take the start of isentropic compression in both the cases as state point 1. Compression ratio is increased so as to follow the same peak pressure as before. Now sketch these two cycles on both P-v and T-s diagrams, and calculate their ideal efficiencies and mean ef- fective pressures. The values of R and cp remain the same.

An air-standard cycle consists of the following processes: isentropic compression from 15°C, 1.01 bar through a compression ratio of 5:1. heat addition at constant volume of 2600 kJ/kg. (i) (ii) reversible adiabatic expansion to the initial volume. heat rejection isochorically. (iii) (iv) For air take R = 0.287 kJ/(kg·K) and cp = 1.005 kJ/(kg·K). Sketch the cycle on P-v and T-s diagrams, and calculate its ideal efficiency, mean effective pressure and peak pres- sure. Take the start of isentropic compression as state point 1. Now the cycle above is modified in two ways so the heat is added, i.e., (a) isobarically, and (b) half isochorically and half isobarically. Take the start of isentropic compression in both the cases as state point 1. Compression ratio is increased so as to follow the same peak pressure as before. Now sketch these two cycles on both P-v and T-s diagrams, and calculate their ideal efficiencies and mean ef- fective pressures. The values of R and cp remain the same.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A newly purchased sedan car operates on an ideal thermodynamic cycle. The engine has a compression…

Q: A cold air-standard Otto cycle has a compression ratio of 12 and the temperature and pressure at the…

A: Given data: r=12p1=14.2 lbf/in2T1=520°RQ=400 Btu/lb Need to determine the the maximum temperature,…

Q: e pressure is 1 bar, and the cylinder volume is 560 cm^3. The maximum temperature during the cycle…

A: Draw the p-v diagram for Otto cycle. Given, p1=1 bar T1=300K v1=560cm3 Tmax=T3=2000K Compression…

Q: Air enters a two-stage compressor operating at steady state at 560°R, 14 Ibf/in.? The overall…

Q: Air enters the compressor of an air-standard Brayton cycle with a volumetric flow rate of 60 m³/s at…

Q: Required information Problem 09.015 - 3-Step Air-Standard Cycle with Constant Specific Heats -…

Q: only need help with letter (d). At the beginning of the compression process of an air-standard…

Q: At the beginning of the compression process of a standard cold air Otto cycle, the air is at 100…

Q: newly purchased sedan car operates on an ideal thermodynamic cycle. The engine has a compression…

Q: Consider an ideal Brayton cycle that has a pressure ratio of 12, a compr t temperature of 300 K, and…

Q: Air enters an air - standard Otto cycle with a pressure and temperature of 1 bar and 15"…

Q: In a Diesel cycle, the air at the beginning of the isentropic compression is at 1 bar and the volume…

A: GIVEN:- P1=1barV1=0.85m3V2=0.78m3T2=690KP4=2.32bar (Pressure at the end of expansion…

Q: Air enters the compressor of an air standard Brayton cycle with a volumetric flow rate of 60m3/s at…

A: Determine the following parameters for the air-standard Brayton cycle: the amount of heat added to…

Q: A cold air-standard Otto cycle has a compression ratio of 6 and the temperature and pressure at the…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: At the beginning of the compression process of an air-standard Otto cycle, p1 = 1 bar and T1 = 300…

Q: volume of 0.004 m3 at 27 o C and 101 kPa. If the displacement volume is 0.0035 m3 and the heat…

A: Given that , V1=0.004m3T1=27°CP1=101kPaVs=0.0035m3

Q: Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 300 K, with a…

Q: Consider an air-standard Otto cycle. At the beginning of the compression process, the pressure and…

Q: A newly purchased sedan car operates on an ideal thermodynamic cycle. The engine has a compression…

A: Given data Compression ratio = 10 Ambient Air pressure = 1 bar Ambient Temperature = 20°C = 293 K…

Concept explainers

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.

Question

An air-standard cycle consists of the following processes:
(i)
isentropic compression from 15°C, 1.01 bar through a compression ratio of 5:1.
(ii)
heat addition at constant volume of 2600 kJ/kg.
(iii) reversible adiabatic expansion to the initial volume.
heat rejection isochorically.
(iv)
For air take R = 0.287 kJ/(kg K) and cp = 1.005 kJ/(kg K). Sketch the cycle on P-v and
T-s diagrams, and calculate its ideal efficiency, mean effective pressure and peak pres-
sure. Take the start of isentropic compression as state point 1.
Now the cycle above is modified in two ways so the heat is added, i.e.,
(a) isobarically, and
(b)
half isochorically and half isobarically.
Take the start of isentropic compression in both the cases as state point 1. Compression
ratio is increased so as to follow the same peak pressure as before. Now sketch these two
cycles on both P-v and T-s diagrams, and calculate their ideal efficiencies and mean ef-
fective pressures. The values of R and cp remain the same.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Trending now

This is a popular solution!

Step by step

Solved in 10 steps with 15 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A newly purchased sedan car operates on an ideal thermodynamic cycle. The engine has acompression ratio of 10. The ambient air pressure is 1 bar while temperature is 21 ºC. Themaximum temperature in the engine is 1600 K. Draw the ideal power cycle and label it.Utilizing the air-standard assumptions, determine (a) the gas temperature at the exits of thecompression and the expansion processes, (b) the specific works of compression, expansionand net, (c) heat supplied to the engine and (d) the thermal efficiency.
I only need help with letters (c) and (d). At the beginning of the compression process of an air-standard Otto cycle, p1 = 1 bar and T1 = 300 K. The compression ratio is 6 and the heat addition per unit mass of air is 1200 kJ/kg. Determine:(a) the maximum temperature of the cycle, in K.(b) the net work, in kJ/kg.(c) the percent thermal efficiency of the cycle.(d) the mean effective pressure, in kPa.
In a Diesel cycle, the air at the beginning of the isentropic compression is at 1 bar and the volume is 0.85 L. The displaced volume of the cycle is 0.78 L, the temperature at the end of the compression process is 690 K, the pressure at the end of the expansion process is 2.32 bar, the specific heat ratio is =1.32, the specific heat at constant volume Cv = 0.75 kJ/kg.K and the gas constant is 287 J/kg.K for air. The compression ratio is: Choose. The specific heat at constant pressure in kJ/kg.K is: Choose. The maximum temperature of the cycle in K is: Choose. The temperature at the end of the expansion process of the cycle in K is: Choose.. the heat rejected in kJ/kg of air is: Choose.
At the beginning of the compression process of an air-standard Otto cycle, p1 = 1 bar and T1 = 300 K. The compression ratio is 8.5 and the heat addition per unit mass of air is 1400 kJ/kg.Determine:(a) the maximum temperature of the cycle, in K.(b) the net work, in kJ/kg.(c) the percent thermal efficiency of the cycle.(d) the mean effective pressure, in kPa.
A compression ratio of 18:1 is utilized in the functioning of an air-standard dual cycle. The temperature is 298 degrees Kelvin, there is 1 bar of pressure, and the volume is 4 liters. The total amount of heat that is added is 6.3 kJ, of which only 30% is added while maintaining a constant volume and the remaining 60% is added while maintaining a constant pressure. What is the temperature after the constant pressure heat addition process in Kelvin?