An air-filled, hemispherical shell is attached to the ocean floor at a depth of 9.3 m as shown in the figure below. A mercury baromet located inside the shell reads 765 mm Hg, and a mercury U-tube manometer designed to give the outside water pressure indicates differential reading of 735 mm Hg as illustrated. Based on these data what is the atmospheric pressure at the ocean surface? Ocean surface

An air-filled, hemispherical shell is attached to the ocean floor at a depth of 9.3 m as shown in the figure below. A mercury baromet located inside the shell reads 765 mm Hg, and a mercury U-tube manometer designed to give the outside water pressure indicates differential reading of 735 mm Hg as illustrated. Based on these data what is the atmospheric pressure at the ocean surface? Ocean surface

Name: An air-filled, hemispherical shell is attached to the ocean floor at
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: An air-filled, hemispherical shell is attached to the ocean floor at a depth of 9.3 m as shown in the figure below. A mercury barometerlocated inside the shell reads 765 mm Hg, and a mercury U-tube manometer designed to give the outside water pressu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A plate in the shape of an isosceles right triangle with side length 4 meters is submerged in water sothat its hypotenuse is facing down, and its right angle vertex is level with the surface of the water. Findthe hydrostatic force on one side of the plate. How can I properly set up the intergral. I thought the answer should be about 147929 N but I could be wrong.
A pressurised vessel contains water with some air above it, as shown in figure 9 below. A multi-fluid manometer system is used to determine the pressure at the air- water interface. Determine the absolute pressure at point F if atmospheric pressure is 100 kPa.(where h1= 24 cm, h2 = 35 cm and h3 = 52 cm) Oil Air Water Mercury h, (A Figure 9
The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown. Determine the gage pressure of air in the tank if h1 = 16”, h2 = 24”, and h3 = 30”. Take the densities of water, oil, and mercury to be 1.94, 1.65 and 26.39 slugs/ft^3, respectively
As shown in the figure, determine the gage pressure on the bottom of the tank in kPa Considering the total gage pressure at the bottom of the tank what will be the absolute pressure if the barometric pressure if 725 torr? AIR P=150mmHG WATER FLUID X SG=3.69 FLUID Y SG=4.69 FLUID Z 120 SG=5.69 1.50
with reference
Properties of Fluids
The gauge pressure of a pneumatic cylinder reads 40 lb/in.? when the Ib/in.?, volume is 30 in.3. The cylinder is compressed until the gauge reads 60 Part 1: What is the absolute pressure before the cylinder gas is compressed? (number only, psi)
1) Determine the Air Pressure at Point A when the other end of the manometer at Point B is open to the atmosphere. 2) If passages at Point B is suddenly closed at 1.5 meters above the mercury surface while the Air Pressure at Point A have already been determined earlier, calculate for the Pressure of Air trapped at Point B. Oil, s=0.87 A Patm Air Br 1.2 m 1.4m Water 1.6 m Mercury
Find surface tension in a soap bubble of 45 mm diameter when the inside pressure is 2.812 N/m2 above atmosphere. (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKETS) The surface tension of the soap bubble (unit is N/m) = _____________ Short Answer
: A U-tube differential manometer is connected to two pipes at A and B. Pipe A Contains oil of Specific Gravity 0.92 and pipe B is carrying water. If the pressure at point A is 125 kN/m2 find the pressure at point B. What is the solution to find "H" as shown in the anawer of the question
Ans is 0.79 m
A tiny steel cube is suspended in water by a string .if the lengths of the sides of the cube are very small ,how would you compare the magnitude of the pressure on the top ,bottom and sides surfaces of the cube .