an AC motor is connected to a 560 V 60 HZ line the motor has a current draw at full load of 53 Amps and a true power of 18700 W whats the power factor of the motor and find the amount of capacitance that should be connected in parallel with the motor to correct the power factor to 100% or unity.

Q: A three phase 250 hp induction motor operates at 0.8 lagging power factor on 440 V, 50 Hz supply.…

A: We have been given induction motor with, HP = 250 Hp Power factor (Cosϕ1) = 0.8 lagging Supply…

Q: A single-phase AC voltage controller has a resistive load R = 10 Ohm, and the RMS input voltage is…

A: First we will find rms value of output voltage.  Output power delivered =       (Rms value output…

Q: A single-phase AC voltage controller has a resistive load R = 10 Ohm, and %3D the RMS input voltage…

A:

Q: a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.4 milli…

A:

Q: A d.c. generator running at 25 rev/s, generates an e.m.f. of 150 V. Determine the percent- age…

A: Given data, Speed,  N1=25 rev/s = 25×60=1500 RPMN2=20 rev/s=20×60 = 1200 RPM EMF of generator E1=150…

Q: Our objective is to construct an eight-pole induction generator utilizing a standard squirrel- cage…

A: Induction GeneratorIt is an asynchronous generator that converts mechanical energy into electrical…

Q: Explain the prime mover in diesel plant and it's energy conversion

A: Given: Explain the prime mover in diesel plant and it's energy conversion.

Q: A single-phase 111-V, 50-Hz supply is connected to a coil with 200 turns of a coil-core assembly as…

A: Given- Single-phase 111-V, 50-Hz supply, E=111 V, Frequency f=50 Hz, Number of turns N=200, To Find-…

Q: In DC generators, lap winding is suitable for ) high voltage, high current low voltage, high current…

A:

Q: Iron losses in a DC machine are independent of variations in

A: The explanation is as follows.

Q: induction motor is rated 5 HP, 75% power factor and 220 V. What approximate size of capacitor (VAR)…

A: We need to find out VAR size for increased power factor

Q: The voltage regulation of an alternator having 0.75 leading power factor load, no-load induced emf…

A:

Q: The rotor winding of the induction motor at no load condition is equivalent to O connected to an…

A: Rotor Winding of the Induction Motor at No load Condition is Equivalent

Q: in lab winding schemes, The-2 induced emf in a coil is emf in .coil for wave winding a) greater than…

A:

Q: O What is the difference between AC and DC coupling?

A: Coupling is the process where we are giving the supply to the any electric circuit may be amplifier…

Q: Identify the effect of the power coefficient for a wind turbine if the power extracted by rotor…

A:

Q: A 120-V-rms 60-Hz sinusoidal voltage appears across a 500-turn coil. Determine the peak and rms…

A: Given:  f = 60 Hz; Erms = 120 V; N = 500 turns Calculate other parameters, The sinusoidal voltage…

Q: Which of the following could dictate the level to which the AC signal can be adjusted?   a. Bias…

A: Alternating current- An alternating current varies sinusoidal in time domain, or to be more specific…

Q: In steam power station: What are the benefits of superheater? What are the Qi advantages of water…

A:

Q: block diagram fro dc motor refrigerator

A: Electrical machines can be either generator, transformer or motors. They can be either Ac machines…

Q: The voltage regulation of an alternator having 0.75 leading power factor load, no-load induced emf…

A: Given: An alternator no load induced emf, Vnl=2400 V Terminal full load voltage, Vfl=3000 V Load…

Q: If two 3-phase induction machines are mechanically coupled with each other. The two machines are…

A: The induction motors are coupled here mechanically. The speed will same for both machines because of…

Q: Find out the primary current and consider the 1:1 turns ratio.

A: Calculation of the primary current and consider the 1:1 turns ratio.

Q: Alternator A (100 kVA, 3-f, 240 V, 60 Hz, 1800 rpm) is operating in parallel with alternator B (125…

A: In this question We need to determine the pf of load. If Alternator A (100 kVA, 3-f, 240 V, 60 Hz,…

Q: A. Draw the extemal characteristics curves series de generators.

A: Please find the attachment below

Q: State Ohm's Law and explain Explain the difference between

A: In this question we will write about ohms law, ac and dc power....

Q: v. With reference to an 50 Hz3 phase alternator explain how P,Q,V and F are controlled.

A: It is asked to explain the control of P (active power),Q (reactive power), V (voltage) and F…

Q: Q10. The rotating machine of Figure Q10 has the following parameters: Lss = 0.18 H, L = 0.06 H, and…

A: Given Source A=2.5 A (DC) Source B =8.5 A(rms), 50 Hz   peak values are Source A=2.5 A Source B=8.52…

Q: 1. Explain electric are discharge V-A characteristic in DC and AC modes.

A: The DC and AC Forms of Arc welding are to basically used to for welding applications which require…

Q: ----- In d.c. generators armature reaction is produced by armature current O none of the mentioned O…

A:

Q: A long shunt compound generator supplies 29 A at 420 V. If the field resistance is 246 Q, the series…

A:

Q: Comment briefly on the relationship between input and output power at varying excitation levels and…

A: Infinite Bus Bar is the bus bar where many(infinite)  synchronous machines are connected.  The…

Q: A synchronous generator generates 370 V at 55 Hz when the field current is 4.4A. The e.m.f generated…

A: Generated emf of the synchronous generator is proportional to is frequency and current.

Q: The figure below depicts the winding of an electric motor. It has a resistance of R = 15.3 and an…

A: The objective of this question is to find the current flowing through the winding of an electric…

Q: Machine has 6 pole pairs and it is supplied with 50 Hz frequency. In order to double rated…

A: In this question, we need to determine the numbers of poles. We know, Speed N= 120f/P

Q: Steam enters an adiabatic turbine at 6 MPa and 550 °C and leaves at 10 kPa and 50 °C. If the…

A: Let, T0=0°C=273 K it is given that at P1 =6 MPa; T1=550°C hence  h1 = 3540 kJ/kg              s1 =…

Q: A dc machine has hysteresis loss of 300 W and an eddy current loss of 200 W when running at 1200…

A: Hysteresis loss Wh=300 W eddy current loss We=200 W The speed is N=1200 rpm Total core loss…

Q: You are given a report that shows 2 different designs of a quadruple stage impulse generator…

A: Design "A" is more suitable for creating impulsive voltage waveforms than Design "B."

Q: a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.2 milli…

A: