An A36 axially loaded 13mm thick tension member is connected to a gusset plate using 5pcs 18mm diameter rivets arranged as shown. Use Fy= 248MPa & Fu=400MPa for the steel plates. Given a=81mm, b=58mm, c=98m, x=80mm, y=84mm and z=91mm. Calculate the net area in mm2 on Path ABE  Express your answer in 2 decimal places.

Q: 2. The beam shown in the figure supports three concentrated loads. Determine the maximum value of P…

A: Determine maximum value of P=?

Q: ure 2 m B 2m 2m D 4m 500 N 700 N 2 of 2 Identify the zero-force members in the truss shown in…

A: Given: AD = 6 m ED = 4 m Horizontal load on D = 700 N (Towards right) Vertical load on D = 500 N…

Q: 75mm eO 6. Determine the net area of the plate element shown. Plate thickness is 10mm. 50mm 65mm…

A:

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: Solution: Given: LL = 25 kN DL = 50 kN U = 1.0 Plate dimensions: 10 x 100 mm Factored load: P = 1.2…

Q: Compute for the linear weight of 10 mm reinforcing bar. (Use the unit weight of the Steel). a 0.692…

A: Solution  Given the dia of steel d= 10mm  So the area will be A=π/4 * 10² 24=25π mm²

Q: Compute for the linear weight of 10 mm reinforcing bar. (Use the unit weight of the Steel). o 0.692…

A: Given data in question  Diameter  Steel bar To find out  Linear weight Note Unit weight of steel =…

Q: . From the riveted bracket shown, find the maximum shearing stress and determine the thickness of…

A:

Q: 2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load…

A: LL = 25 kNDL = 50 kNU = 1.0Plate dimensions: 10 x 100 mmFactored load:P = 1.2 DL + 1.6 LL = (1.2x50)…

Q: 3 m 1.5 m hinge A B E D 2 m 4 m

A:

Q: For the beam shown, EI = 24 × 10° kip-in² over the length of the beam. The slope (rad) of the beam…

A:

Q: Permissible As in sechion to ensure tensile Compute the design strength of beam shown it 420 MPa ,…

A: To find : Design strength

Q: 6.8 Problem: A bracket shown in figure 6.8 carries an eccentric load of 80 kN at an eccentricity o…

A:

Q: Determine the type and amount of stress in each member of the truss shown below due to wind load…

A: A truss is an assembly of members such as beams that are connected through nodes and form a rigid…

Q: The pin support at A has a double-shear steel bolt as shown. Determine the required diameter of the…

A:

Q: A flat bar tie is connected to a gusset plate by bolt as shown in Fig. 1. Determine the tension…

A: Design ultimate strength of S 275,M20 bolts are usedt= 20 mmThere will be 2 types of failure

Q: Plate t = 8mm C230x19.9 M20 Bolts Ag = 2,530 mm² d = 229 mm T. %3D tw 5.90 mm 80 %3! by = 61 mm ty =…

A:

Q: A rack is made from roll-formed sheet steel and has the cross section shown. Determine the location…

A: Consider the diagram shown below. The length of each segment with respective to their centroid is…

Q: Determine the moment of each force about the bolt located at A (Figure 1). Take Fa = 50 lb. Fc = 50…

A:

Q: *use hand written by Computing the LRFD&ASD in steel design nscp 2015 ty <3

A: Step 1: Calculate Moment of Inertia to solve for ry in KL/ry which is the maximum value of KL/r. ry…

Q: A double bolted lap joint in used to connect two plates of 10 mm thickness using M20 bolt of grade…

A: Joint:Type: Double bolted lap jointPlate thickness: 10 mmBolt:Grade: M20Material: 4.6 (assumed to be…

Q: Give me right solution

A: Given data L8×6×12 Steel used is A572 gr. 42 Diameter of bolt=1 in.

Q: A prismatic bar is fixed at edges A and B as shown in figure. What is the axial force in CD portion?…

A: Given data- A prismatic bar fixed at edges A & B as shown- To Find- The value of the axial…

Q: Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1 = 50, y2 =…

A: Given data in question  Load Dimensions  To find out  Maximum force in a bolt due to load alone

Q: The group of 6-bolts connection subjected to eccentric load P=30 kips as shown in figure. The…

A: Given a bolted assembly, it is required to find the maximums hear force.

Q: A coper road is inserted into a hollow aluminum cylinder. The copper rod projects 0.130 mm as shown…

A: Assume the load in the copper rod be PC & in the aluminum rod be as PAl: P=PC + PAl…

Q: Two plates are connected by a bolt as shown in the figure. What is the shear stress on the bolt? D…

A:

Q: Figure below shows an eccentric bolted connection. Four bolts of 16 mm diameter are provided to…

A:

Q: Per missible As in section to ensure tensile Compute the design strength of beam shown if fy = 420…

A: To find : design strength

Q: Find the Zero- Force Members at the shape: D. 10 A M 10 ft 10 t 10 A 10 A 10 ft 10 t 10 A 6 kips 6…

A: To find the zero force members-

Q: determine the minimum bolt diameter

A: Given data:P=230 KN or 230×103NAverage shear stress,τavg=125 MPa or 125 N/mm2

Q: Select the reinforcing needed for the short tied column shown for the following: Pn=2000 kN, 250 mm,…

A: INTRODUCTION: Columns are the standing upright structure which transfer the above superstructure…

Q: The bolts used for connecting the angle shown in the figure are 22mm in diameter. The thickness of…

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.