An 800-kg rigid pile P is driven into the ground using a 300-kk hammer H. the hammer falls from rest at a height yo = 0.5 m and strikes the top of the pile. Determine the impulse which the hammer imparts on the pile if the pile is surrounded entirely by loose sand so that after striking, the hammer does not rebound off the pile. (Ans : 683 Ns)

An 800-kg rigid pile P is driven into the ground using a 300-kk hammer H. the hammer falls from rest at a height yo = 0.5 m and strikes the top of the pile. Determine the impulse which the hammer imparts on the pile if the pile is surrounded entirely by loose sand so that after striking, the hammer does not rebound off the pile. (Ans : 683 Ns)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4
Does the location of the shear center depend upon the applied loading?
From the beam shown, determine the maximum normal stress. In MPa.
The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and 2014-T6 aluminum alloy respectively. When the temperature is at 65° F, ACE is in the horizontal position. Figure 1.5 in. -0.25 in. C 3 in. 1 of 1 اساساسا Part A Determine the vertical displacement of the pointer at E when the temperature rises to 160 ° F. (Figure 1) Express your answer with the appropriate units. SE = Value Submit Request Answer Provide Feedback Units ?
Part A The turbine develops 230 kW of power, which is transmitted to the gears such that both B and C receive an equal amount. The rotation of the 100-mm-diameter A992 steel shaft is w = 720 rev/min. (Figure 1) The journal bearing at D allows the shaft to turn freely about Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include appropriate units. its axis. µA ? Value Units max Submit Request Answer Figure 1 of 1 Part B Determine the rotation of end D of the shaft relative to A. Use Gst = 75.0 GPa. Express your answer to three significant figures and include appropriate units. 1.5 m µA ? 2 m Value Units 1 m Submit Denuest Anewer
A gear motor can develop 2010 W when it turns at 231 RPM. If the allowable shear stress for the material of the shaft connected to it is Tallow = 88.3 MPa, determine the smallest diameter of the shaft to the nearest mm that can be used. 14 mm 21 mm 22 mm 9 mm 17 mm 2 mm
Determine the maximum diameter of the hole that could be punched out of a 30-mm thick metal sheet with a punching force of 200 kN. The shear strength of the plate is 350 MPa
Urgently required
Draw the three Mohr’s circles that describe the following state of stress.
Approve that? k - P = = (₁ + ² = 1 M²) ² ·(1 P 2 Po k - P = = (₁ + ^² = 1 M²) = ²1 (1 P 2
Verify the equality of the following shearing stresses: (2) σεν = σνε (b) σzz =σ22
The long bolt passes through the 70.4-mm-thick plate. If the force in the bolt shank is 9.5 KN, then the average shear stress (MPa) along the cylindrical area of the plate defined by the section lines a-a is: O a. 0.00 O b. 21.00 O c. 2.39 O d. 4.77 O e. 1.19 18 mm b b 8 mm Time left 0:45:52 a 7 mm YouTube The wood beam has an allowable shear stress of 15 MPa, the maximum shear force V (kN) that can be lind to the cross section is: