An 80 cm long bar contracts axially by 0.2 mm when a compressive load is applied to it. Determine the strain and the percentage strain? [Ans. 2.5*10“, 0.025%]
Q: A steel cube of side length L = 0.5 m is subjected to a shearing force of 5000 N along the top…
A: Length=0.5m Shear force=5000N Shear constant=8.3×10^10N/m2 Shearing angle=?
Q: A thin rectangular plate is uniformly, deformed, as shown. Determine the shear strain Yxy at P.…
A: Solution: The shear strain of the thin rectangular sheet in the y-direction can be obtained using…
Q: A load 1 kg produces a certain extension in the wire of length 3 m and radius 5 x 10-4 m. How much…
A: To find- Lateral strain=? Given- Load (M)=1 kgLength of wire (L)=3 mRadius (r)=5×10-4mYoung's…
Q: When an axial load is applied to the ends of the bar shown in the figure, the total elongation of…
A: Given Elongation of the bar between A dan C δtotal = 0.22 in Strain ε2…
Q: a) Sketch a stress-strain diagram for a metal indicating the proportional limit, yield point,…
A:
Q: The cross-sectional dimensions of the beam shown in the figure are a = 5.0 in., b = 5.5 in., d = 4.6…
A: Concept: To determine the Maximum Tension and Compression Bending Stress we will divide the Cross…
Q: A solid cube of side 0.1 m is subjected to a shearing force of 1000 N. The top surface of the cube…
A: To find-(1) shearing stress(2) shear srain(3) modulus of rigidityGiven-F=1000 NL=0.1 mx=0.22×10-3…
Q: The bonded single lap joint shown below has a width, w = 97 mm and an overlap length, I = 28 mm. =…
A: Given that: Overlap length I = 28 mm Thickness h = 1.1 mmwidth w=97 mmTensile load F=4385 NShear…
Q: I Find the maximum at A. Take V- 5000N ↓ Imm 140 mm A shear stress & the shear stress 20mm 100mm I…
A:
Q: Two solid cylindrical rods (1) and (2) are joined together at flange Band loaded, as shown. The…
A: ANSWER :- As in question normal stress is asked and can be calculated as force/area. Area of rod 1…
Q: A steel rod 55 cm long has a diameter of 35.0 cm. The compressive strength (the maximum stress it…
A:
Q: Find the longitudinal stress to be applied to wire to decrease it's Liameter uniforenly by 10%…
A: We need to compute-Longitudinal stress =?The data given as-Lateral strain=10%=110Poisson's ratio…
Q: A solid copper cube has an edge length of 89.3 cm. How much stress must be applied to the cube to…
A:
Q: the maximum compressive load a bone
A: Given: Outside radius is ro=2 cm Inside radius is ri=1.5 cm Maximum stress is σ=153 MPa Note: 1…
Q: Ex. 65: A steel wire of diameter 1 mm and length 2 m is stretched by applying a force of 2 kg wt.…
A: We need to compute-(i) Increase in length (l)=?(ii)Strain=?(iii) Stress=?The data given as-Diameter…
Q: A tendon is subjected to tensile forces. The cross-sectional area of the tendon is 0.0002 m2. If the…
A: See below
Q: Determine the outside diameter of a tube if the stress is limited to 128 MN/m2 and a hollow steel…
A:
Q: A wire of uniform cross sectional area of 0.25 mm2 is stretched at both ends by a total force of 65…
A: Given data The cross-sectional area is given as Ac = 0.25 mm2. The total force at both ends is…
Q: A tangential force of 0.004 KN affected the upper surface of a rectangle 5 mm high, 3 cm long and 5…
A: Given Dimensions, l=3 cm= 3×10-2mw=5 cm=5×10-2mh=5mm=5×10-3m Tangential force, F=0.004 KN= 4N…
Q: An object weighs 4.5 x 105 N is supported by steel cable, with cross-sectional area of 6.0 cm 2, the…
A: Given: The weight of the object is 4.5x105 N. The cross-sectional area is 6 cm2. Young's modulus of…
Q: A structural steel bar with a 3.6 in. x 0.890 in. rectangular cross section is subjected to a…
A:
Q: Four wire of the same material but having different lengths subjected to same load. Which of the…
A: To find- Length of wire. Combination of length (L) and radius (r) which has highest elongation.…
Q: A square steel plate has area Im² and thickness 5 cm. The bottom edge is fixed. A tangential force…
A: Shear modulus, also known as Modulus of rigidity, is the ratio of shear stress to shear strain that…
Q: A cubic marshmallow is 3 cm on each side sitting in a room at atmospheric pressure (1.01x105 Pa).…
A: Original side of cube is Pressure is The new side of cube is The pressure at which volume expands is…
Q: te=120 (2) 457 tレ Oa = 60 the figure (0,c=0), find the principal Q-For the plane stress case shown…
A: Given : A plane stress case.
Q: The lower surface of metal cube, having each side of length 10 cm, is kept fixed and tangential…
A: We need to compute-Force applied (F)=?The data given as-Length (L)=10 cm=0.1 mDisplacement (x)=0.1…
Q: The young modulus of a material whose elastic strain and stress are 1.53 and 169.42 N/m²…
A: The elastic strain, strain=1.53 The stress, stress=169.42 N/m2
Q: A load 1kg produces a certain extension in the wire of length 3m and radius 5x10-*m. How much will…
A: We need to compute the lateral strain produce in the wire.The data that has been provided is-Load…
Q: Ex. 13: A cube of side 5 cm each whose upper face is displaced by 0.65 cm due to a force of 0.25 N.…
A: We need to compute-(i) Shearing stress=?(ii) Shearing strain=?(iii) Modulus of rigidity=?The data…
Q: Find the strain of a brass rod of length 250mm which is subjected to a tensile load of 50kN when the…
A: Given, The length of the rod, L=250mm The tension on the rod, T=50kN The extension of the rod,…
Q: R [6r – (4)a a Find the maximum velocity for the velocity profile shown here (an expression based on…
A:
Q: Q. 8: Strain energy per unit volume is given by 1 (stress)? 1 (b) 2 * (stress)* y (a) 2 y 1 strain 1…
A: We know, Strain is produced in the wire due to application of load. Hence. work is done on…
Q: Referring to Fig. compute the maximum force P that can be applied by the machine operator, If the…
A:
Q: A hollow metal post is 10 ft long, and the cross-sectional area of the material is 2.5in² . When a…
A: Stress is defined as the force per unit area. Strain is defined as the ratio of change in…
Q: . Strain energy of the stretched wire is 18 × 10-³ J and strain energy per unit volume of the same…
A: We need to compute-Volume of wire (V)=?The data given as-Strain energy per unit volume=6×10-3…
Q: A 3.5 cm cube of unknown metal has a shear modulus of 5.0x 10°N/m ? absorbed a force of 0.40 N.…
A:
Q: A sphere of copper has a radius of 8.00 cm and is compressed uniformly by a force of 5.00 × 108 N.…
A:
Q: Find the elongation of a rod made of aluminum and copper under a tension of 5.8×103 N. The…
A: Given information: Here, R is the radius of the rod, T is the tension, LAl and LCu are the length…
Step by step
Solved in 2 steps with 4 images