An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total uniform load of 45 kN/m all throughout its length. STEEL DECION CIVIL ENGINEERING Beam properties: A = 11,500 mm² bf = 250 mm tw = 10 mm d == 350 mm If=: 16 mm lx = 266 x 10 mm If the Beam is laterally supported throughout the beam a) Determine the Maximum Bending Stress b) Determine the Maximum Web Shear Stress c) To strengthen the beam, 2- 200 mm x 10 mm cover plates, one at the top of the flange and the other at the bottom of the flange were added. What is the resulting maximum bending stress?

An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total uniform load of 45 kN/m all throughout its length. STEEL DECION CIVIL ENGINEERING Beam properties: A = 11,500 mm² bf = 250 mm tw = 10 mm d == 350 mm If=: 16 mm lx = 266 x 10 mm If the Beam is laterally supported throughout the beam a) Determine the Maximum Bending Stress b) Determine the Maximum Web Shear Stress c) To strengthen the beam, 2- 200 mm x 10 mm cover plates, one at the top of the flange and the other at the bottom of the flange were added. What is the resulting maximum bending stress?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 7. [Concepts: Allowable stresses and factor of safety] Two aluminum rods AB and AC support a vertical load P. The allowable tensile stress for the aluminum is Gallow = 150 MPa. a) If P = 20 kN, determine the required diameters of the rods AB and AC. b) If the diameters of the rods AB and AC are 10 mm and 8 mm, respectively, determine the largest vertical force P that can be supported. U B
NEED ANSWER ASAP!! A so-called "trapeze bar" in a hospital room provides a means for patients to exercise while in bed (see figure). The bar is 2.1m long and has a cross section in the shape of a regular octagon. The design load is 1.6kN applied at the midpoint of the bar, and the allowable bending stress is 240 MPa. Determine the minimum height h of the bar. Round to one decimal place. (Assume that the ends of the bar are simply supported and that the weight of the bar is negligible.) hmin=___mm
O FS = 2.4 O FS = 2.2 Consider a simple supported beam subjected to the load shown. The beam has a solid square cross-section with edge "a", and made of steel alloy having a yielding tensile and compressive strength of oy = 400 MPa. Determine its minimum required edge "a" for a factor of safety against yielding FS = 2.5. The area moment of inertia of that section about its neutral axis N.A. is INA = b.h³/12. of 3 kN 2 kN/m D 6 m + Select one: 5:37 PM 86°F Light rain ENG 6/18/2021 hp
Problem- A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E= 2 × 10 N/mm². The elongation of the bar will be
Pls solve it
4.15 Knowing that for the casting shown in the figure the allowable stress is 6 ksi in tension and 15 ksi in compression, determine the maximum couple M that can be applied.
If the maximum bending stress at section a–a is not allowed to exceed an allowable stress of 220 MPa, determine the maximum allowable force P that can be applied to the end E.
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
Experts Pleae help ASAP
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the stress in the steel of the section in PART B in MPa.0
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 520 mm?. If the stress in the bar must not exceed 650 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 8 m, b = 4.8 m, and c= 10.4 m. (1) B' a Answer: P = i kN