An 18mm diameter rivet is used to fasten two 22mm thick plate. If the shearing stress is 60 MPA. What tensile force applied each plate to shear the bolt? ( Ans F=15.27KN )

Q: 2. A rigid bar, hinged at one end, is supported by two identical springs as shown in the Fig. Each…

A:

Q: Problem 4 only, solve carefully, include the units in every step and draw the diagram. Thanks! A…

A:

Q: The pins at C and A are in double shear, and the pin at B is in single shear. All pins have a…

A:

Q: A 100in. diameter cylinder (closed ends) made of a material having an allowable yield strength in…

A: The given data are: d=100 inτ=10000 psiP=300 psi Here, d, τ, and P represent the diameter, allowable…

Q: A helical spring is made by wrapping wire 25 mm in diameter around a forming cylinder 150 mm in…

A:

Q: For the figure shown below, compute the shear force in section 1. Neglect the weights of the member.…

A:

Q: A flanged bolt coupling is used to connect a solid shaft 110 mm in diameter to a hollow shaft 100 mm…

A:

Q: 4. Determine the efficiency of the riveted butt joint with 20 mm main plate, 12 mm cover plates and…

A: We have to determine efficiency of riveted butt joint

Q: In a cruise ship, a liferaft is hanged by suspending it with a thick metallic cable attached to both…

A: Given,  Tension in the cable , T = 40 KN Maximum allowable shear stress  = 50 * 106 Pa

Q: The butt joint shown in the figure is connected using five 20 mm diameter bolt. If the tension force…

A:

Q: The ultimate shearing stress of the rivet used to join plates is 22 ksi. For a factor of safety of…

A:

Q: Determine the shear force acting at each of the following locations: (a)x= 2m (b)x= 4 m (c) x 8 m…

A: (a) Consider the free-body diagram of beam and calculate the shear force at x=2 m.

Q: A circular dis of lead of radius 150 mm and thickness 50 mm is reduced to a thickness of 25 mm by…

A:

Q: 1.5 (A). A simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded…

A:

Q: A flanged bolt coupling is used to connect a solid shaft 94 mm in diameter to a hollow shaft 100 mm…

A:

Q: In the below figure, if the shear stress on the bolt shown in the first figure is 60 MN/m2. The…

A: Consider the shear force diagram for the first figure,

Q: Example: The coupling shown in Fig. below is constructed from steel of rectangular cross-section and…

A: For the given coupling  P = 50 kN  dia of bolt (d) = 15 mm  To determine  (i) the shear stress in…

Q: Q6 A screw clamp as shown in the figure, exerted load (30KN), and the type of thread is (Tr.70×8.5).…

A: exerted load= 30 KNThe type of thread is  ( Tr. 70 x 8.5)Stress for nut = 60 MPaLength of the nut =…

Q: One hole will be formed on plate sheet with ultimate shear stress = 1.5 kN/mm2. If compression…

A: According to question given data Hole diameter = 700 mm Compression stress = 600 N/mm2 Ultimate…

Q: "ood is 90 MPa, ar ces in the glue are MPa respectively. 00 N,

A:

Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…

A:

Q: 8. In the figure, a setup for testing an adhesive is prepared. For this, a rubber 15 kN block was…

A: Given, Total shear Force (F)= 15+15=30kN Total shear area (A) = 80×60=4800×2=9600mm2 Modulus of…

Q: A flanged bolt coupling is used to connect a solid shaft 120 mm in diameter to a hollow shaft 100 mm…

A:

Q: 2. A solid steel rod with a diameter of d = 50mm is subjected to a bending moment M = 1.5 kN-m and a…

A:

Q: Two square bars (15mm thick) are bolted together as shown. Volt's allowable shear stress is 90 MPa,…

A:

Q: 3. The members of the structure in figure below weigh 280 lb/ft. Determine the smallest diameter pin…

A:

Q: Although the shear stress induced on the pin is significant, it is also subjected to crushing…

A:

Q: Ise the graphical method to construct the shear-force diagram and identify the magnitude of the…

A:

Q: Two solid rods (1) and (2) of the same material are joined together at flange B and loaded as shown…

A:

Q: A rectangular post which is made up of two blocks of wood glued together along a joint inclined at…

A:

Q: What is the yield strength in shear of a rod with a maximum allowable shear stress of 140 MPa if a…

A:

Q: ring stress in the head of the bolt: of the washers if their inside diam

A:

Q: A figure below is a 200-mm diameter pulley which was attached on a 60-mm diameter shaft and it…

A: Given data Diameter of shaft = d  = 60 mmApplied Torque = T= 2200 Nm Allowable shearing stress = 70…

Q: Suppose the load in the figure below is 2 kN. Further suppose that the distance between the load and…

A: Given : P= 2kN The distance between load and centroid is 1.3 m The horizontal distance between bolt…

Q: In the clevis shown in Fig. 1-11b, the minimum bolt diameter (d=22mm) and the minimum thickness of…

A: Given data  Diameter = 22 mm Thickness = 10 mm Shear stress = 83 MPa Bearing stress = 138MPa Find…

Q: bolt having a diameter to fasten two timbers as shown in the figure load in the bolt of 34 kN. 1.…

A:

Q: 3. A vertical load of 500 N acts at the end of a rectangular cantilever beam 2 m long and 25 mm…

A: Given : load P = 500 Nlength of beam L = 2 m = 2000mmwidth of beam b = 25 mmBending stress  = 130…

Q: 4. A small race car has an aluminum hub (shown in red). The drive axle is press-fit into the hub,…

A: