An 18-lb block A slides in a vertical frictionless slot and is connected to moving support B by means of a spring AB of constant k=8 lb/ft. Knowing that the acceleration of the support is a=am sinwft where am =5 ft/s? and wf=6 rad/s, determine (a) the maximum displacement of block A, (b) the amplitude of the fluctuating force exerted by the spring on the block. An 18-lb block A slides in a vertical frictionless slot and is connected to a moving support B by means of a spring AB of constant k=8 Ib/ft. Knowing that the acceleration of the support is a=asin a,t. where a =5 fus and w, =6 rad/s, determine (a) the maximum displacement of block A, (b) the amplitude of the fluctuating force exerted by the spring on the block. a d sin @ft B.

An 18-lb block A slides in a vertical frictionless slot and is connected to moving support B by means of a spring AB of constant k=8 lb/ft. Knowing that the acceleration of the support is a=am sinwft where am =5 ft/s? and wf=6 rad/s, determine (a) the maximum displacement of block A, (b) the amplitude of the fluctuating force exerted by the spring on the block. An 18-lb block A slides in a vertical frictionless slot and is connected to a moving support B by means of a spring AB of constant k=8 Ib/ft. Knowing that the acceleration of the support is a=asin a,t. where a =5 fus and w, =6 rad/s, determine (a) the maximum displacement of block A, (b) the amplitude of the fluctuating force exerted by the spring on the block. a d sin @ft B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The tyre of a parked car in a parking lot experiences Select one: O Siding Friction O Rolling Friction Both static and dynamic friction O Static Friction
i need the answer quickly
B10
Give answer in your own words. Thanks
12
Describe the principles of comparators and its qualities in field of engineering
Number 4
Solution 1: Ergonomic Assessment and Improvement. An ergonomic assessment of Paula's workstation could identify areas where adjustments could be made to reduce strain on her wrists. This could include adjusting the height of the workstation, providing wrist supports, or changing the design of the tools she uses. The strength of this solution is that it directly addresses the physical strain causing Paula's discomfort. However, the weakness is that it may require investment in new equipment or tools, and the effectiveness will depend on the specific changes made. Solution 2: Job Rotation. Paula could be rotated between different tasks more frequently, reducing the amount of time she spends on tasks that strain her wrists. This could also include training other workers to perform the welding and gaging operations, allowing for more flexibility in task assignments. The strength of this solution is that it reduces the repetitive strain on Paula's wrists. The weakness is that it requires…
The possibility to make the required shape from the material is considered during design specification. Select one: O True O False
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Speed
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…