Show fbd and box answers All truss members in the truss shown aremade of the same material and are of thesame cross-sectional area. The failurenormal tensile stress for the material is16ksi, and the failure compressive normalstress is 10 ksi. A factor of safety, FS, of 1.6 isto be applied. The internal forces in eachmember can be computed using statics. As ahint, it was predetermined that the maximumforces occur at members DE and AD.Determine the following by using 4 decimalplaces:*Magnitude and type of axial force inmember DE.Magnitude and type of axial force in*member AD.* The required area in in2 for truss memberDE.* The required area in in2 for truss memberAD* What is the minimum required cross-sectional area in in2 for all the members ifthey are to be of the same size? 2 kipE1 ft45°45B

To find force and area of members

All truss members in the truss shown are made of the same material and are of the same cross-sectional area. The failure normal tensile stress for the material is 16ksi, and the failure compressive normal stress is 10 ksi. A factor of safety, FS, of 1.6: to be applied. The internal forces in each member can be computed using statics. As hint, it was predetermined that the maximu forces occur at members DE and AD. Determine the following by using 4 decima places:

All truss members in the truss shown are made of the same material and are of the same cross-sectional area. The failure normal tensile stress for the material is 16ksi, and the failure compressive normal stress is 10 ksi. A factor of safety, FS, of 1.6: to be applied. The internal forces in each member can be computed using statics. As hint, it was predetermined that the maximu forces occur at members DE and AD. Determine the following by using 4 decima places:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

No copy paste from other sources. Write your own answer! Q. Describe the importance of penetration testing?
4. Complete the accompanying set of profile notes and perform the arithmetic check. Provide a sketch of this project's profile view. (You can use excel to sketch) Station BS (ft) HI (ft) IS (ft) FS (ft) BM1 0+00 1+00 2+00 3+00 3+35 4+00 TP1 5+00 5+20 5+30 6+00 BM2 4.58 4.87 2.59 3.79 4.82 4.98 5.05 7.30 4.60 4.78 4.85 4.89 11.21 10.58 Elevation (ft) 427.06
B- What are the common sources of error associated with measurements?
feedback is used by Schmitt trigger Your answer
(b)- A page of a level with some missing readings is reporduced below. Fill in the missing entries along with the necessary arithmetical checks. Station I.S F.S Rise 1 2 3 4 5 6 7 8 9 10 11 Total = B.S 3.650 X -2.170 X 6.490 X 2.830 3.640 2.410 2.320 3.000 X X 2.420 2.750 Fall 1.320 2.750 1.320 R.L 108.260 Remark
Do not include the unit in writing the answer. Use small letters (lowercase) in writing the words. Complete the table below. Area Cut or fill? 15.0 1 45.0 12 2 22.0 12 3 4 27.0 Ţ 6.5
What Are Common Data Modeling Errors?
When someone says "Standard Error," what does that mean?
4.
how did you get the expected error