Air stream (k = 0.02439 W/m.K, v = 1.426 x10 ' m2/s, Pr = 0.7336) flows over a flat surface [L= 4.5 m, w = 2.5 m] with velocity of 158 km/hr, flow is parallel to L, What is the average convective heat transfer Coefficient "W/m?.°C" ? %3D

Air stream (k = 0.02439 W/m.K, v = 1.426 x10 ' m2/s, Pr = 0.7336) flows over a flat surface [L= 4.5 m, w = 2.5 m] with velocity of 158 km/hr, flow is parallel to L, What is the average convective heat transfer Coefficient "W/m?.°C" ? %3D

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.39P

See similar textbooks

Similar questions

Mass flow rate of hot fluid is 0.007 kg/s. Convection heat transfer coefficient of hot fluid stream is 1000 W/m?.°C. Thermophysical properties are given as follows. Hot fluid; c, = 5000 J/kg.°C Water; dynamic viscosity, µ = 0.001 Pa.s; Prandti number, Pr = 6.14; thermal conductivity, k = 0.607 W/m.°C; density, p = 1000 kg/m³; specific heat c, = 4200 J/kg.°C. Neglecting conduction resistance of the pipe, calculate heat exchanger effectiveness (ɛ), heat transfer rate (Q in J/s), outlet temperatures of the hot fluid (Thout) and water (Tw.out) for varying mass flow rate values of water provided below. Mass flow rate of water, m (kg/s) 0.0025 0.01 0.025 0.05 0.075 0.1 Plot heat exchanger effectiveness (ɛ), heat transfer rate (Q in J/s), outlet temperatures of the hot fluid (Thout) and water (Tw.out) as a function of water mass flow rate (m .). Comment on the results. Hot fluid in (65 °C) Water Water in (25 °C) out d = 0.5 cm Hot fluid out L= 5 m
Mass flow rate of hot fluid is 0.007 kg/s. Convection heat transfer coefficient of hot fluid stream is 1000 W/m? °C. Thermophysical properties are given as follows. Hot fluid; c, = 5000 J/kg.°C Water; dynamic viscosity, u = 0.001 Pa.s; Prandtl number, Pr = 6.14; thermal conductivity, k = 0.607 W/m.°C; density, p = 1000 kg/m2; specific heat c, = 4200 J/kg.°C. Neglecting conduction resistance of the pipe, calculate heat exchanger effectiveness (ɛ), heat transfer rate (Q in J/s), outlet temperatures of the hot fluid (Th,out) and water (Tw.out) for varying mass flow rate values of water provided below. Mass flow rate of water, m (kg/s) 0.0025 0.01 0.025 0.05 0.075 0.1 Plot heat exchanger effectiveness (:), heat transfer rate (Q in J/s), outlet temperatures of the hot fluid (Thout) and water (Tw.out) as a function of water mass flow rate (m). Comment on the results. Hot fluid in (65 °C) Water Water in (25 °C) out d = 0.5 cm Hot fluid out L = 5 m
* ZAIN IQ liı. SuspendEA IN A ROom, Ana TS Subjected To Air Flow Parallel To I... A 2m by 3m flat plate is suspended in a room, and is subjected to air flow parallel to its surfaces along its 3m long side as shown in the figure. The free stream air temperature, T, is 20°C and the velocity is 7 m/s. The total drag force acting on the plate is measured to be 0.86 N. Determine the average convection heat transfer coefficient for the plate. Air 20°C, 7 m/s L= 3 m. This problem has been solved! See the answer
Solve fast please
Topic: Heat transfer Completely solve and box the final answer. A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.72 W/m deg C, Re=3840000, and Pr=0.7)?
A fluid (Prandtl number, Pr = 1) at 500 K flows over a flat plate of 1.5 m length, maintained at 300 K. The velocity of the fluid is 10 m/s. Assuming kinetic viscosity, v = 30 x 10-6 m²/s, the thermal boundary layer thickness (in mm) at 0.5 m from the leading edge is (up to three decimal)?
i need the answer quickly
Topic: Heat transfer Completely solve and box the final answer. 6. Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20degC to 60degC. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. What is the heat absorbed by the water?
Please correct answer
Air at 30 °C and 1 atm is flowing over a long flat plate with a velocity of 10 m/s. Its corresponding kinematic viscosity (y) is 1.5625x10 m2/s. The distance from the leading edge of the plate where the flow becomes turbulent is V. Oa. 1m Ob. 0.976 m 0.781 m Od.1242 m
An isothermal long cylinder with square (side of 0.4 m and diagonal of 0.5657 m) cross-section is placed in a flow with a velocity of 1 m/s as shown. The properties of the fluid are: kinematic viscosity is 1.38 x 10-5 m²/s, thermal conductivity is 0.024 W/m.°C, and Prandtl number is 0.73. What is the average Nusselt number for the flow? 1253 a Figure 1: Flow configuration for Problem 6. The dimensions are: a=0.4 m, b=0.5657 m
Topic: Heat transfer Completely solve and box the final answer. Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20degC to 60degC. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. Determine the Reynolds number.