Air flows through a long, isentropic nozzle. The temperature and pressure at the reservoir are 1000K and 20 atm, respectively. If the Mach number at the entrance is 0.2, determine the gas velocity at the entrance. 634 m/s O127 m/s 478 m/s 254 m/s For a large centrifugal pump, the required net positive suction head is typically around O 5 ft 2 ft 15 ft

Air flows through a long, isentropic nozzle. The temperature and pressure at the reservoir are 1000K and 20 atm, respectively. If the Mach number at the entrance is 0.2, determine the gas velocity at the entrance. 634 m/s O127 m/s 478 m/s 254 m/s For a large centrifugal pump, the required net positive suction head is typically around O 5 ft 2 ft 15 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air flows through a converging-diverging (c-d) nozzle. It is supplied from a large air reservoir in which the temperature is 446 K and the pressure is 190 kPa. The velocity and the cross- sectional area at the nozzle exit are 594 m/s and 0.0005 m^2, respectively. Find the Help me solve this problem :followings of dynamic gases
Mach number at a certain section in a diverging part of a c-d nozzle is 0.7. At farther section (towards the exit), Mach number reduces to 0.4. Hence, the cross-sectional area of the farther section is greater by
100% High pressure water and compressed air are delivered to some operating rooms. Bored one day, with no patients around, you take the cap off the nozzle to see what would happen. Water flows through the vertical pipe and nozzle and then exhausts into the air as shown in the diagram. The water pressure in the pipe at position 1 is 3 atm. The pressure when the water discharges to the air is 1 atm. Position 2 identifies the nozzle, 0.75 m above position 1, where the water flow has been constricted from an 8-cm diameter pipe to a 3-cm diameter nozzle. Assume that the free jet remains a stream of water with a 3-cm diameter. Assume no friction losses. Free jet -3 cm diameter 0.75 m a) Determine the mass flow rate of water through pipe at position 1 in kg/s. 3 atm 8 cm diameter b) Determine the height, h, the water jet can rise. c) Calculate the friction factor inside the 8-cm pipe and determine if the assumptions of negligible friction losses was reasonable. Water AR d 128 PM 10/3/2021…
Air enters a turbine at temperature and pressure of 800°C, 10bar respectively. The actual exit airtemperature is 180°C. The turbine isentropic efficiency is estimated to be 85%. Calculate the turbine exit pressure and the actual expansion index (n).
What happens to steam pressure and velocity in a diverging nozzle?
A large tank supplies helium through a converging-diverging nozzle to the atmosphere. Pressure in the tank remains constant at 8.00 MPa (abs) and temperature remains constant at 1000 K. There are no shock waves in the nozzle. The nozzle is designed to discharge at an exit Mach number of 3.5. The exit area of the nozzle is 100 mm². Determine the mass flow rate through the device. For helium: specific heat ratio k = 1.66; ideal gas constant R = 2077 J/kg.K. To = 1000 K Po= 8 MPa (abs) Throat Helium A₁ = 100 mm² Ma₁ = 3.5
! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Steam enters a converging nozzle at 5.0 MPa and 400°C with a negligible velocity, and it exits at 3.0 MPa. It has a nozzle exit area of 50 cm². Determine the exit velocity, mass flow rate, and exit Mach number if the nozzle is isentropic. The exit velocity is m/s. kg/s. The mass flow rate is The exit Mach number is
Calculate the thrust of a turbojet engine with an inlet diameter of 4 ft. If an airplane is flying at altitude of 15km at Mach 0.8 with an exit velocity of 900ft/s. The turbojet engine thrust at 15-km. (in Lbf)
HANDWRITTEN: Learjet 35 is a multi-role business jet and a military transport aircraft equipped with tail-mounted turbofan engines. This business jet has a cruising speed of 480 mph and cruising at an altitude of 45,000 ft. The ambient pressure and temperature is 390 R and 310 psfa, respectively. If the compressor has a pressure ratio of 18:1 and the maximum operating temperature is 2885 degrees Fahrenheit. Compute for the (a) compression ratio, (b) volume and temperature at each point, (c) Heat added and Heat rejected (d) Wnet (item c), (e) Brayton work (based on compressor and turbine work), and (f) efficiency. Note: Make sure to indicate a CORRECT P-V and T-S diagram