Air flows at a velocity of 90 m/s down a 20 cm diameter pipe. The air is at a pressure of 120 kPa and a temperature of 30°C. A valve at the end of the pipe is suddenly closed. This valve is held in place by eight mild steel bolts each with a diameter of 12 mm. Will the bolts hold the valve without yielding? Assume that the pipe is discharging the air to the atmosphere and that the ambient pressure is 101 kPa. It will be necessary to look up the yield strength of the steel to answer this question.

Air flows at a velocity of 90 m/s down a 20 cm diameter pipe. The air is at a pressure of 120 kPa and a temperature of 30°C. A valve at the end of the pipe is suddenly closed. This valve is held in place by eight mild steel bolts each with a diameter of 12 mm. Will the bolts hold the valve without yielding? Assume that the pipe is discharging the air to the atmosphere and that the ambient pressure is 101 kPa. It will be necessary to look up the yield strength of the steel to answer this question.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Identify the state of the fluid: Water at 1002kPa, with a specific entropy of 6.586 kJ/kgK
Theworkdonetocompressonemoleofmonatomicidealgasis6200J. The temperature of the gas changes from 350 to 550 K. How much heat flows between the gas and its surroundings? Determine whether the heat flows into or out of the gas. (Internal energy of monatomic ideal gas: U=3nRT/2, where n = no. of moles, in mol R = Universal gas constant = 8.314 J/mol.K T = temperature, in K)
The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible. If the specific enthalpy of fluid and velocity of fluid at the inlet are 3,160 kJ/kg and 241 km/hr respectively. At the exit the specific enthalpy of fluid is 2,693 J/kg. Calculate the velocity of the fluid at the exit of the nozzle in m/s,
hi, can you solve this question ? The A and B tanks given in the figure are separated from each other by the closed valve between them. The water vapor in tank A has a volume of 0.2 m3, a temperature of 150 ° C and a pressure of 100 kPa. Tank B is filled with saturated water vapor in a volume of 0.3 m3 at a pressure of 300 kPa. Then, the valve between the tanks is opened and the final pressure is 175 kPa as a result of the mixing of the fluids in the tanks with each other and sufficient heat transfer. According to this:a) Temperature (C) and phase of the fluid in the final state;b) Find the amount of heat transfer in the process result.
Air is flowing in the wind tunnel in the laboratory. The temperature in the laboratory is 22°C and the height of the column of mercury in the barometer in the laboratory is 634 mm. The liquid in the manometer being used to measure the vacuum in the wind tunnel is oil having a specific gravity of 0.826, and the manometer reading is 125 mm . The wind tunnel is on the CU campus in Denver where g = 9.796 m/s² . a) Find the atmospheric pressure of the air in the laboratory (answer: 84092 Pa). b) Find the absolute pressure of the air in the wind tunnel (answer: 83081 Pa). c) Find the density of the air in the wind tunnel (answer: 0.981 kg/m³). Air at 22°C → h = 125 mm Oil, SG = 0.826
A large tank is divided into two equal volumes. One half of the tank is filled with saturated water of unknown quality at temperature = 320 °F. The other half of the tank is evacuated (i.e there is nothing in it). When the partition separating the two halves breaks, the water will expand to fill the entire tank. The temperature is unchanged, and the final pressure is given below. Determine the quality of the water before the partition broke. Water isothermal jacket P=0 m = 0 Pfinal = 80-psia
Hot gas enters the turbine at a pressure of 600kPa and a temperature of 1200K at a speed of 60m / s and exits at a pressure of 300kPa and a speed of 70m / s with a cross-sectional area of 0.125m ^ 2. Assume isotropic and constant flow and hot gas as a complete gas with a molar mass of 25kg / kmol and γ = 1.35 turbine power.
An iron bar 2.0 cm x 3.0 cm x 10.0 cm at a temperature of 95 °C is dropped into a barrel of water at 25 °C. The barrel is large enough so that the water temperature rises negligibly as the bar cools. The rate at which heat is transferred from the bar to the water is given by the expression Q (J/min) = UA (T₁-T) where U = 0.05 J/(min cm °C)] is a (cm) is the exposed surface area of the bar, T, and T are the surface temperature of the bar and the water temperature, respectively. The heat capacity of the bar is 0.46 J/g °C). Heat conduction in iron is rapid enough for the temperature T, to be considered uniform throughout the bar. a) Write an energy balance on the bar b) Plot the expected plot of T, versus t and then curve fitting. M = (60 cm³) (7.7 g/cm³) = 462 g C, = 0.46 kJ/(kg-°C), T = 25°C U= 0.050 J/(min-cm².°C) 4 = 2[(2)(3)+(2)(10)+(3)(10)]cm² = 112 cm²
The water level in a tank is 20 m above the ground. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, and the air pressure above the water surface is 2 atm gage. The system is at sea level. Determine the maximum height to which the water stream could rise.
Quick -sol
In a water distribution system, the temperature of water is observed to be as high as 30°C. Determine the minimum pressure allowed in the system to avoid cavitation.
In a reservoir, the pressure of a compressed gas must not be increased past 825 kPa. The gauge indicated 388 kPa when the temperature is 24oC. Determine the maximum temperature which can safely be attained in the reservoir