Don't Make any Mistake Or else i will Downvote. Air contained in a variable-loadpiston-cylinder is initially at 0.1 m3,22°C, and 100 kPa. The cylinder isthen placed in a hot water bath at100°C where the air begins absorbingheat at a constant rate of 0.5 kW. After some time it is observed that thetemperature has remained relatively constant, however the volume hasdoubled. Determine the amount of time (seconds) that has past.Answer: At = 13.86 secondsplease show steps.

Answered: Image /qna-images/answer/af572c05-700c-44cd-a898-109dff435919.jpg

Air contained in a variable-load piston-cylinder is initially at 0.1 m3 , 22°C, and 100 kPa. The cylinder is then placed in a hot water bath at 100°C where the air begins absorbing eat at a constant rate of 0.5 kW. After some time it is observed that the emperature has remained relatively constant, however the volume has doubled. Determine the amount of time (seconds) that has past.

Air contained in a variable-load piston-cylinder is initially at 0.1 m3 , 22°C, and 100 kPa. The cylinder is then placed in a hot water bath at 100°C where the air begins absorbing eat at a constant rate of 0.5 kW. After some time it is observed that the emperature has remained relatively constant, however the volume has doubled. Determine the amount of time (seconds) that has past.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Adjustable Link L m Pivot Pivot Screw 'B' Gripper In the drawing, arm A is being driven back and forth in the direction of the arrows. It is connected to a gripper by way of an adjustable link L, two horizontal bars and two vertical bars. Screw B is a shoulder screw secured to arm A, but allows the horizontal bar to pivot around it. If the shoulder screw B was lowered towards the end of arm A, and the stroke of arm A remained the same, the stroke of the gripper would: Arm 'A' 0 MIMINIA
DO THIS TYPEWRITTEN AND COMPLETE FOR UPVOTE
PART 3. VELOCITY ANALYSIS OF ROTATING CRANKS. INSTRUCTIONS: ON A SEPARATE PIECE OF BOND PAPER. SHOW THE COMPLETE SOLUTION AND FINAL ANSWER OF THE FOLLOWING PROBLEMS. 3,600° 1. The instantaneous angular velocity of the crank Q2A is counterclockwise. Q2A = 1.5 in. Find the second instantaneous linear velocity. And draw a graphical interpretation showing the proper length and direction of the velocity arrow of Q2A. Velocity scale: 0.5 in = 10 in/s. Drawing scale: 1:1 2.50 1.50 60° 60°
Q7: For the epicyclic gear train shown, determine the speed of the arm. Planet gear Arm Sun gear Ring gear Gear 1, sun, RPM 1200, Number of teeth 20, Planet Gear , Number of teeth 30 Ring Gear, Rotates RPM 120, and teeth of 80,
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A gear reduction system consists of three gears A, B, and C. Gear A rotates clockwise with a constant angular velocity wA = 1200 rpm. 2 in 2 in. 4 in. 6 in. Determine the accelerations of the points on gears B and C which are in contact. The acceleration of the point on gear Bis[ The acceleration of the point on gear Cis lin./s2 +. in./s2 →,
- once answered Correctly will UPVOTE!!
Match the items in columnsI and II. Column I P. Addendum Q. Instantaneous center of velocity R. Section modulus S. Prime circle Column II 1. Cam 2. Beam 3. Linkage 4. Gear (a) P-4, Q-2, R-3, S-1 (b) P-4, Q-3, R-2, S-1 (c) P-3, Q-2, R-1, S-4 (d) P-3, Q-4, R-1, S-2
To program the motion of tool according scheme below you must write L CW Current position ΤΟ Stop line Sj→ SI Drive line Gi-CI O S1, CCW, C1, L, TO, S1 O S1, TO, S2 O C1, CW, R, TO, S1 O S1, CW, R, TO, C1 O C1, CCW, S1, L, TO, S1 O C1, PAST, S1
Alert for not submit AI generated answer. I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image formet and hand writing