Air at 20°C flows over a flat plate having a uniform heat flux of 800 W/m². The flow velocity is 4m/s and the length of the plate is 1.2 m. Determine the value of heat transfer coefficient and also the temperature of the plate as the air leaves the plate.

Air at 20°C flows over a flat plate having a uniform heat flux of 800 W/m². The flow velocity is 4m/s and the length of the plate is 1.2 m. Determine the value of heat transfer coefficient and also the temperature of the plate as the air leaves the plate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 0.4-W cylindrical electronic component with diameter 0.3 cm and length 1.8 cm and mounted on a circuit board is cooled by air flowing across it at a velocity of 240 m/min. If the air temperature is 35°C, determine the surface temperature of the component. For air properties evaluations assume a film temperature of 50°C. Is this a good assumption?
Water at 43.3°C flows over a large square plate at a velocity of 20 cm/s. The plate is 2 m long (in the flow direction) and its surface is maintained at a uniform temperature of 10.0°C. The width of the plate is 2 m. Calculate the steady rate of heat transfer for the entire width of the plate in watts (W). The properties of water at the film temperature of (Ts + T∞)/2 = (10 + 43.3)/2 = 27°C are p = 996.6 kg/m³, k= 0.610 W/m-°C, μ = 0.854 x 10-3 kg/m-s, and Pr = 5.85. The steady rate of heat transfer per unit width of the plate is W.
i need the answer quickly
In the effort to increase the removal of heat from a hot surface at 120°C, a cylindrical pin fin (kf = 237 W/m.K) with diameter of 5 mm is attached to the hot surface. Air at 20°C (1 atm) is flowing across the pin fin with a velocity of 10 m/s. Determine the maximum possible rate of heat transfer from the pin fin. Evaluate the air properties at 70°C.
In an experiment, a metallic cylinder 12.7 mm in diameter and 94 mm long is heated internally by an electric heater and subjected to a cross flow of air. The velocity and temperature of the air were V = 12 m/s and T = 26.2°C, respectively. The heater power dissipation was measured to be P = 48 W, and the surface temperature was maintained at T 128.4°C. Neglect heat loss by radiation and conduction. (a) Determine the convection heat transfer coefficient from the experimental %3D %3D %3D observation. (b) Compare the experimental result with the convection coefficient computed from Zhukauskas relation. Assume, for air at T = 300 K: v = 15.89x10° mʻ/s, k= 26.3x10³ W/m.K, Pr= 0.707; for air at T, = 401 K: Pr= 0.690. %3D 08. %3D Show all calculations. Air k-L
An average person body surface is approximately 2.0 m². Its skin temperature is 33°C. The convection heat transfer coefficient of a clothed person walking is expressed as h = 9.0 V0.53 for velocities 0.5 m/s< V <2 m/s, where V is the walking velocity. Assuming the average surface temperature of the clothed person to be 30°C , determine the rate of heat loss from an averaged man walking in Chill air at 7 °C: T; (a) 0.5 m/s (b) 1.0 m/s (c) 1.5 m/s (d) 2.0 m/s Air
A long aluminum wire of diameter 3 mm is extruded at a temperature of 280°C. The wire is subjected to cross air flow at 20°C at a velocity of 6 m/s. Determine the rate of heat transfer from the wire to the air per meter length when it is first exposed to the air.
The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa Air at this pressure and 20°C flows with a velocity of 8 m/s over a 1.5 mx6 m flat plate whose temperature is 140°C as shown in Fig below. Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 6-m-long side.
Air at a pressure of 1 atm. abs. and 50°C flows parallel to the top surface of a rectangular plate, 2 m x 9 m. Its temperature is maintained at 150°C. The air velocity is 8 m/s. If the critical Re no. is 106, determine the rate of heat transfer from the plate if the air flows parallel to (i) the 2 m long side (ii) the 9 m long side
Can you help me with my homework.
Mercury at 25°C flows over a 3-m-long and 2-m-wide flat plate maintained at 75°C with a velocity of 0.01 m/s. Determine the rate of heat transfer from the entire plate.
7-115 Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.8-m-long tubes inside which the refrigerant is evaporating at –20°C. Air approaches the tube bank in the normal direction at 0°C and 1 atm with a mean velocity of 5 m/s. The tubes are arranged in-line with longitudinal and transverse pitches of SL = ST = 1.5 cm. There are 25 rows in the %D flow direction with 15 tubes in each row. Determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. Evaluate the air properties at an assumed mean temperature of -5°C and 1 atm. Is this a good assumption? 0.8 m Air 0°C 1 atm ST = 1.5 cm 5 m/s 0.8 cm 1.5 cm/ S, = Refrigerant, –20°C FIGURE P7–115