Aggregate from three sources having the properties shown in table below were blended at a ratio of 25:60:15 by weight. Determine the properties of the aggregate blend. Property Aggregate 1 Aggregate 2 Sand Coarse aggregate angularity, percent crushed faces Bulk specific gravity Apparent specific gravity 73 95 N/A 2.774 2.390 2.552 2.810 2.427 2.684

Q: Handwritten/ neat work pls show the steps on how u got the areas and not just the answers. Parts d,…

A: A framing plan is given we need to find out the tributory areas

Q: Hello could you include the converting process in the step 3? It's quite confusing

A:

Q: Give details of JPCP, JRCP, and CRCP with necessary figures.

A: In pavement construction, three different concrete pavement design types are commonly used: Jointed…

Q: What are the similarities and difference between the actual ASTM C143 standard and the procedure…

A: In ASTM C143, the test method includes the determination of the hydraulic cement concrete slump in…

Q: All fixed metal parts that are within_ft horizontally of the inside walls of a permanently installed…

A: The question asked is descriptive.

Q: TABLE 9.5(a) - MINIMUM THICKNESS OF NONPRESTRESSED BEAMS OR ONE-WAY SLABS UNLESS DEFLECTIONS ARE…

A: Minimum girder depth as per ACI

Q: -Q2.23-. A cantilever beam shown is reinforced with 7- 25 mmø at the top and 4- 16 mmø at the…

A: db (diameter of tie bars) = 12mm C.C (clear cover) = 50mm Lets C.S be clear spacing between…

Q: What is the definition of a chill plate?

A:

Q: L = 14 in. PA L = 16 in. ds da Ps d1= 2" d2= 2.375" d3= 2.25" d4= 2.5"

A:

Q: m REQUIREMENT: PCS- "THICK INTERIOR PLYWOOD WALLS PCS- ¼" THICK EXTERIOR HARDIFLEX WALLS PCS-…

A:

Q: *Water flows at a rate of 2.0 ft³/s in an old, rusty 6-in-diameter pipe that has a relative…

A:

Q: Design the most efficient, rectangular, concrete (n=0.015) channel to carry a flow of 2,500-ft³/sec,…

A:

Q: CONSTRUCT 4 A 4B A SUMMARY TABUL & PLOT Fc = 6000 PS1 fy = 60 ks2 Fe 4000 PS1 Fy = 60 KSI 23 26 14"…

A: Beam AWidth= 14in ; Eff. Depth= 20.5in ; depth of NA= 4.45in ; Strain in concrete= 0.003 ; Strain in…

Q: = What is the gage pressure [in psi]... Water Air Oil (SG=0.8)

A: Given:Required:Gage pressure at bottom of tankGage pressure in the air zone in the container

Q: 13m Fo=7KN 6M N FB-5KN Y Find Equivalent System @ O

A: The question is to find the equivalent system at point Y. The diagram shows a beam supported at two…

Q: @ * 30" 16" 14" 16" 6" Uncracked. M = 60 (1) ftop ?? (2) f bottom=? ft-k

A:

Q: (5) 8" 3#9 12" 8" 44 17" #3" fó= 3000 psi, Grade 60 steel NWC, &M₁=?

A:

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.