Advantages and goods of Cyber security in a business, at least 500 words,

Q: 3. Compute the flexural stresses in the concrete and steel for the beams shown using the…

A:

Q: 2.13 The rainfall recorded at the network of stations due to a storm over a trapezoidal water- shed…

A:

Q: . A 40m steel tape is suspended in the air between a theodolite and vertical rod, which is placed…

A:

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: to find  the force in members

Q: A centralized IP-based building security system saved money since it was easier to administer.

A: IP system means internet protocol system.To protect the business from any theft, intrusion and…

Q: The center-line of a new railway is to be set out along a valley. The first straight AI bears 75⁰…

A: Here distance T1I is assumend as 300 m

Q: 5. Sieve analyses were performed on two soils. The table below summarizes the results of these…

A: Given:- The result of the sieve analyses are given  Sieve No.  Diameter Percent passing for Soil…

Q: A plane slices a right circular cone parallel to its base at the midpoint of its height. The radius…

A: To calculate the volume of the cone below the plane.   Given, Radius of the cone (R) = 4 in Height…

Q: 1. Which failure criterion is used to interpret the results from a direct shear test? Why? 2. Which…

A: This question is related to the Soil Strength from Geotechnical Engineering. In this question , ask…

Q: RITING ITLED d. What is the difference in elevation between TP15 and TP30? (Ans.) e. What is the…

A:

Q: 2. Determine the cracking moment for the section if f' = 28MPa and a modulus of rupture fr=0.71 √28…

A: Given:- The compressive strength of the concrete (f'c) = 28 MPa The modulus of rupture (fr) = 0.7×28…

Q: An initially rectangular element of material is deformed as shown in the figure. The shear strain in…

A: To find the shear  strain in the section

Q: With the aid of an illustration, describe two methods by which areas bounded by irregular lines can…

A: Areas bounded  by irregular lines can be found by using midoridnate rule , trapezoidal method ,…

Q: 300 mm PDL = 15 kN/m , PLL = 5 kN/m 2 - 16mm 4m 5m 3m 450 mm fel - 20 Z MPa 4 - 25mm

A: Note:- As per guidelines we are allowed to solve first three supports in case of multiple sub-parts…

Q: Width U/S of dam = 49.3 , length of spillway = 23.8 , head above crest 5.5 if approach velocity will…

A:

Q: The gravel, sand, silt and clay contents of five different soils are given below. Classify the soils…

A:

Q: Provide an example of a product or system that uses international standard (such as bank card size ,…

A: There are several aspects where the standards are followed internationally. In case of traffic…

Q: 1. Find the volume of concrete needed to fill the slump cone for the test. 2. Find the volume of…

A:

Q: What form of architecture is most suited to the realm of social networks?

A: Architecture can only be utilized to design the crossover locations, eliminate obstacles, and create…

Q: 1. Find the volume of the pyramid with the given radius=2.886 PLAN -2.886 and a height of 7.00 cm.…

A:

Q: The 80-mm-diameter shaft is made of steel. The shaft is subjected to a triangular distributed load…

A: Given:- The diameter of the shaft = 80 mm  The shaft is loaded with triangular distributed load per…

Q: 2. Determine whether each of the trusses below are internally determinate, indeterminate, or…

A:

Q: Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have,…

A: Consider the given data The coordinate of the point A 60,0,0 The coordinate of the point B 0,120,20…

Q: Determine the forces in all the members, and state if these members are in tension or compression.…

A: Support reaction: ∑MC=0RA×8-600×4-900×12=0RA=1650 N∑FY=0RA+RC-600-900=01650 +RC-600-900=0RC=-150 N

Q: 6 m 2 m 2 m, ,2 m, B C 8 kN 2 m. 2 m H 8 kN E 2 m G F 8 kN Consider the truss shown. It is supported…

A:

Q: 1. A line was measured to be 3256.35m using a 30m steel tape supported throughout its length under a…

A:

Q: Draw the shear, moment, elastic curve, and axial force diagram of this frame. Provide the summary of…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Communication barriers faced by engineers

A: Barriers in communication lead to many problems which waste both time and money. In the field of…

Q: El 38m w.S. 1. The section of a cofferdam is as shown in the figure. If the coefficient of…

A:

Q: Somm ,75mm fc' = 20.7 MPa, fy = 415 MPa, Strength based %3D 25mm Gomm condition was considered.…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: 3. The loads on a steel beam consist of 150 kN due to dead load and 410 kN due to live load. No…

A: Design Load combination (LRFD) :- 1.2DL + 1.6LL + 0.8WL Allowable load combination (ASD):- DL +…

Q: 1. Determine the nominal moment strength of the beam 4 #36 300 mm 420 mm 500 mm 80 mm Jy = 420 MPa f…

A: Given : Required : Nominal moment strength of beam

Workplace Safety

A workplace can be referred to as a space where people work together for the accomplishment of a common goal of the organization. Here, people can be a worker, an employee, and an employer. A person can be said to be an employer if he/she gets the job of organizational goal accomplishment through other persons, and that person gets paid for his/her service. All employees can also be referred to as workers. An employer may also hire workers of other categories which require specialized skills to finish a work. Both employees and workers along with the employer form the primary occupants of a workplace.