Answered: Ľ X 10Nms w 100 kg R 50N 45° N 600-x m | bartleby

Related questions

Question

Write the equation of the motions only. The given square-shaped rigid body is capable of both translational and rotational motion within the two-dimensional plane of the page. The length of each side of the square measures 0.2 meters. Furthermore, the body possesses a mass moment of inertia of 15 kg m².

Ľ
X
10Nms w
100
kg
R
50N
45°
N
600-x
m

Expert Solution

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

The figure shows three 0.0186 kg particles that have been glued to a rod of length L=5.67 cm and negligible mass. The assembly can rotate around a perpendicular axis through point O at the left end. If we remove one particle (that is, 33% of the mass), by what percentage does the rotational inertia of the assembly around the rotation axis decrease when that removed particle is (a) the innermost one and (b) the outermost one? Axis (a) Number Units (b) Number Units
Two uniform, solid spheres (one has a mass M and a radius R and the other has a mass M and a radius Rb=2R are connected by a thin, uniform rod of length L=2R and mass M. Note that the figure may not be to scale. Find an expression for the moment of inertia I about the axis through the center of the rod. Write the expression in terms of M, R, and a numerical factor in fraction form.
The wheels of a wagon can be approximated as the combination of a thin outer hoop, of radius r = 0.156 m and mass 4.32 kg, and two thin crossed rods of mass 7.80 kg each. A farmer would like to replace his wheels with uniform disks = 0.0525 m thick, made out of a material with a density of 5990 kg per cubic meter. If the new wheel is to have the same ta %3D moment of inertia about its center as the old wheel about its center, what should the radius of the disk be? = PA rd
A 4kg ball with a 0.45-meter radius is initially at rest begins to roll and accelerate at a uniform rate to a velocity of 10 rad/s in 5 seconds. The rotational inertia of the ball is 0.243 kg*m^2. Calculate the magnitude of the torque on the ball. Answer must use the correct SI units.
A thin, hollow sphere of mass 2.30 kg and radius 0.610 m is rolling on a horizontal surface with a constant angular speed of 61.0 rpm. What fraction of the kinetic energy is translational kinetic energy, and what fraction of the kinetic energy is rotational kinetic energy?
You are riding your bicycle down the street at a speed of 16 m/s. Your bicycle's frame has a mass of 6.0 kg, and each of its two wheels has mass 2.2 kg and radius 0.34 m. Each wheel can be thought of as a hollow hoop (assuming that the rim has much larger mass than the spokes). What is the total kinetic energy of the bicycle (in Joules), taking into account both the translational and rotational motion?
The figure shows three 0.0146 kg particles that have been glued to a rod of length L-5.58 cm and negligible mass. The assembly can rotate around a perpendicular axis through point O at the left end. If we remove one particle (that is, 33% of the mass), by what percentage does the rotational inertia of the assembly around the rotation axis decrease when that removed particle is (a) the innermost one and (b) the outermost one? (a) Number (b) Number Axis Units Units 0 m m m |a+d+d+
A force vector, F = 3i− 12j, acts at a distance vector of r = 0.2i m from the axis of rotation on a wheel. It has a moment of inertia of 3 kgm^2. If we assume the full mangitude of the torque causes rotation, what is the angular acceleration caused by the force?
The figure shows three 0.0114 kg particles that have been glued to a rod of length L= 5.70 cm and negligible mass. The assembly can rotate around a perpendicular axis through point O at the left end. If we remove one particle (that is, 33% of the mass), by what percentage does the rotational inertia of the assembly around the rotation axis decrease when that removed particle is (a) the innermost one and (b) the outermost one? Axis m m (a) Number i Units (b) Number i Units >