According to the Working at Height Regulations, state: a) the minimum height at which precautions should be taken

Q: What is overfire air (OFA)?

A: Overfire Air (OFA) systems are used to redirect an amount of the combustion air away from the…

Q: Prepare the details estimate for the following 2 roomed building

A: In this question, we have to calculate the total estimate of works

Q: At what height is it necessary to install guardrails? O Sec 26.3 (1) O Sec 26.3 (2) O Sec 26.3 (3) O…

A: sec 26.3(2) where height is necessary to install the guardrails.

Q: *8-24. Determine the slope at B and the maximum displacement of the beam. Use the moment-area…

A:

Q: G K H

A: Given data:

Q: Estimate the needed fire flow rate and volume required to provide adequate protection to 2-Story…

A: Given data: Effective floor area = 1200 sq. m Area of floor (A) = 1200 m2 For a two-story joisted…

Q: Q5. What is the minimum clearance required by OSHA regulations between a crane and a 150-kV power…

A: The Occupational Safety and Health Administration(OSHA)-The Occupational Safety and Health…

Q: 3. Determine the gutter and the downspout size requirement of the following roof detail: Assign 2…

A:

Q: Are there any regulations in the world and in Turkey for construction vibration levels? Explain.

A: There is a new regulation which was titled as "Noise Protection and Sound Insulation in Buildings"…

Q: From the wind load design perspective, why do inclined roofs are preferred over flat roofs in…

A: Inclined roofs are preferred over flat roofs in low rise buildings because of the following reasons:

Q: Provide the sanitary waste pipe size if the pipe is carrying 400 fixture units and sloped at 1/8”…

A: Here, in the given problem we are only provided with the following data-- 1. SANITARY waste  2.…

Q: Determine the gutter and the downspout size requirement of the following roof detail: Assign 2…

A:

Q: Draw the Shear and Moment Diagram in the beam shown elow by AREA METHOD. Show the complete area of…

A:

Q: 11-24. A drained triaxial test is performed on a sand with of, - ojs 500 kPa. At failure, Tmax 660…

A: Solution for 11-28 as asked   From the given data, Initial void ratio e0 = 0.8 Initial volume of…

Q: Describe about the vibrodisplacement procedure.

A: Vibro displacement is the ground improving method that is designed for compacting solid ground…

Q: What would the minimum gutter size and slope for a roof that is 40 feet x 20 feet with a design…

A: Given data- Dimensions of the roof =40 feet×20 feetDesign rainfall=4 inch To Find- The minimum…

Q: For the given failure surface of the soil, the unit weight for both the soil A and B is 19 kN/m³. O…

A: Given data- Failure surface of the soil is shown in figure- Unit weight of both soils = 19 kN/m3,…

Q: State any four safety related acts and regulations to be observed when carrying out underground…

A: Underground works: Drilling, blasting, guniting, rock bolting, and soft soil work are examples of…

Q: DRAINAGE PIPE AND VENT SIZING - USE RNPCP 1999. - CONSIDER THIS PLAN FOR A RESIDENTIAL BUILDING WITH…

A:

Q: A fence with dimensions of 15m long by 20m high including portions below NGL. Determine the number…

A:

Q: A E 6 m D 4 m 4 m B P₁

A:

Q: The inflow and outflow hydrographs of a reservoir routing are shown below inflow(m/sec) 27…

A: Given data- Inflow hydrograph- Outflow hydrograph- To Find- The values of the peak attenuation…

Q: What are the techniques for retrofitting?

A: Techniques of RETROFITTING

Q: Why the installation of a barrier at about frost depth is done. Describe about the barrier and for…

A: Most generally, the freezing layer defined with freezing depth is the extent with which the surface…

Q: Write Safety Work Statement of any potential hazard in the construction site

A: Introduction- Construction site safety is a component of development activities that serve to…

Workplace Safety

A workplace can be referred to as a space where people work together for the accomplishment of a common goal of the organization. Here, people can be a worker, an employee, and an employer. A person can be said to be an employer if he/she gets the job of organizational goal accomplishment through other persons, and that person gets paid for his/her service. All employees can also be referred to as workers. An employer may also hire workers of other categories which require specialized skills to finish a work. Both employees and workers along with the employer form the primary occupants of a workplace.