b) P, = Pt- Pe= 100 – 16 = 84 wattc) P2 = 2AJ (ß) = 2 x 100 x 3(3.8) = 34 watt%3DACH.WFCA carrier signal given by 10 cos 2n x 10°t volt is FM modulated by single toHzmessage 4 cos 2n x 103t volt if the modulation constant is 1000Ama) Compute max. frequency deviation and deviation ratio.A. FVoltFmb) Write the equation of modulated wave. Acc) Sketch the spectrum.d) Calculate sidebands carrier and total power.42

Answered: Image /qna-images/answer/adb76151-c73c-4c52-86d7-c1c0bd67740e.jpg

AC H.W FC A carrier signal given by 10 cos 2n x 10°t volt is FM modulated by single to Hz 4 cos 2n x 103t volt if the modulation constant is 1000 message Am Volt Fm a) Compute max. frequency deviation and deviation ratio.A.F b) Write the equation of modulated wave. Ac c) Sketch the spectrum. d) Calculate sidebands carrier and total power.

AC H.W FC A carrier signal given by 10 cos 2n x 10°t volt is FM modulated by single to Hz 4 cos 2n x 103t volt if the modulation constant is 1000 message Am Volt Fm a) Compute max. frequency deviation and deviation ratio.A.F b) Write the equation of modulated wave. Ac c) Sketch the spectrum. d) Calculate sidebands carrier and total power.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q. Choose the correct answer (.. 1. increases as the length of channel increases. (interference, distortion, additive noise, attenuation). 2. 100% modulation is produced in AM when carrier frequency exceeds signal frequency, amplitude equals signal amplitude, amplitude exceeds signal amplitude). 3. A 10 MHz carrier of peak value of 10 V is amplitude modulated by a 10 kHz signal of amplitude 5 V. The amplitude of each sideband frequency is 4. A Phase-Locked Loop (PLL) is a feedback circuit consisting of VCO, all of the above). 5. The line connecting the positive and negative peaks of the carrier waveform is called (Peak line, Maximum amplitude, Modulation index, Envelope) 6. Thermal noise power is proportional to (T², 1/T, T, T'2) 7. Which of the following is an advantage of SSB over DSB? (No change in spectrum space, Reduce in spectrum space, Carrier is suppressed, Power is not wasted on the carrier). 8. Which one of the following is not true with respect to SSB signal? (Hard to…
ver is in the side dulation factor m. This emphasis .8. A carrier wave of 500 watts is subjected to 100% amplitude modulation. Determine: (ii) power of modulated wave. (i) power in sidebands Solutien
Problem 5. A carrier wave of frequency 20 MHz is frequency-modulated by a sine-wave of amplitude 2 volts and frequency 4 kHz. The frequency sensitivity of the modulator is 10 kHz per volt. a) Determine the approximate bandwidth of the FM wave using Carson's rule. b) Repeat part (a) assuming that the amplitude of the modulating wave is doubled. c) Repeat part (a) assuming that the modulation frequency is doubled.
Q2. For the scheme shown in Figure Q2, Draw the spectrum of the baseband signal (multiplexer output) for the multiplexer. Determine the bandwidth of the baseband signal (multiplexer output) for the multiplexer. Determine the minimum transmission bandwidth of the multiplexer. Explain, briefly, the modification needed for the multiplexer in the figure to achieve this bandwidth. i. ii. ii. 4 kHz cos 10,000xt Baseband signal 2 kHz cos 24,000nt cos 2000nt cos 32,000nt Figure Q2
A carrier signal given by 10cos27Tx108t volt is FM modulated by single tone message 4cos2Tx103t volt if the modulation constant is 1000 Hz/Volt a) Compute max. frequency deviation and deviation ratio. b) Write the equation of modulated wave. c) Sketch the spectrum. d) Calculate sidebands carrier and total power
3. The role of mixer in the Armstrong modulator is to. a) raise the carrier frequency b) lower the carrier frequency c) to change the carrier frequency to any required value For AMDSB-SC, The carrier is suppressed using a) A mixer b) A frequency multiplier c) A balance modulator 5. In FM modulation, frequency deviation is equal to .........., if the amplitude of the modulating signal is 4 V, and the frequency sensitivity of the modulator is 30 Hz/V. a) 120 Hz b) 34 Hz c) 100 Hz 6. A voltage controlled oscillator (VCO) is an oscillator that its frequency output is varied according to any change in the ............... at its input. 4. a) Frequency b) Current c) Voltage Q1: (B) Draw A block diagram to generate the SSB using Hilbert Transform method, Write an equation for an input, and output signals?
100 MHz carrier wave has a peak voltage of 5 volts. The carrier is frequency modulated (FM) by a sinusoidal modulating signal or waveform of frequency 2 kHz such that the frequency deviation Af is 75 kHz. The modulated waveform passes through zero and is increasing at t= 0. Determine the expression for the modulated carrier waveform.
B. FM modulated signal is transmitted over a noisy transmitter modulator, with the power spectral density of noise being as shown in Figure 1 (W is the information frequency with 1 KHz, Sn (f) is the power spectral density for the noise). The FM equation and transmitter is shown in figure 2. 1. Derive the FM modulated signal for narrowband modulation 2. Determine the power of the narrowband FM modulation 3. Determine the signal to noise ratio for the narrowband FM modulation s4) - A, co 2f1 + 2n, mr dr 2 mk, Baseband signal Narrowband Integrator phase modulator Frequency maltiplier FM signal N4. Crystal- contralled oscillator Figure 1 Figure 2
Q6. Figure Q6 shows the line spectrum of a modulated signal (all components are positive and real). 3 1 232 234 236 238 frequency/kHz Figure Q6: Line spectrum of a modulated signal (a) Describe the modulation scheme. (b) What are the values of the carrier frequency, modulation frequency and the modulation index? (c) What is the transmission efficiency (ratio of modulated to total power) in this example? (d) The reception of this signal is undertaken with a superheterodyne detector using an intermediate frequency of 110 kHz. What is the appropriate local oscillator frequency? (e) Demodulation of this type of signal is usually accomplished using an envelope detector. Describe the principles of operation of an envelope detector and sketch an example circuit. (f) What considerations should be made about the component values in the design of an envelope detector in order to demodulate the signal after shifting to the intermediate frequency? Relative unitsS
H.W A carrier signal given by 10cos27×108t volt is FM modulatedby single tone message 4cos2nx103t voltif the modulation constantis 1000 HzlVolt a) Compute max. frequency deviation and deviation ratio. b) Write the equation of modulatedwave. c) Sketch the spectrum. d) Calculate sidebands carrierand total power.
All information about current transformer and voltage transformer in protection system