able Bodies; CEE23; 2S; AY21-22 - Summative Assessment 2- DLSU-D formable Bodies; CEE23; 2S; AY21-22 The plate of thickness, t 5 mm, is loaded with the following stress; s = 100 MPa, sz = -60 MPa, E = 200 GPa, v = 0.33. If a = 160 mm, and b = 200 mm, D A Calculate the change in thickness (mm). Select the correct response: 0.0045 -0.0045 -0.0023 0.0023

able Bodies; CEE23; 2S; AY21-22 - Summative Assessment 2- DLSU-D formable Bodies; CEE23; 2S; AY21-22 The plate of thickness, t 5 mm, is loaded with the following stress; s = 100 MPa, sz = -60 MPa, E = 200 GPa, v = 0.33. If a = 160 mm, and b = 200 mm, D A Calculate the change in thickness (mm). Select the correct response: 0.0045 -0.0045 -0.0023 0.0023

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

15 kip Specific Weight y Elasticity E Rigidity G (Ib/in") Modulus of Modulus of Yield Strength (ksi) Materials (10) ksi (10) ksi Tens. Comp. Shear A - Structural A36 - Stainless 304 - Tool L2 0.284 29.0 11.0 36 36 Steel 0.284 28.0 11.0 30 30 Alloys 0.295 29.0 11.0 102 102 2 ft 4 kip 4 kip The A-36 steel bar shown in the figure is made from two segment shaving cros OSS- B sectional areas of AAB-lin^2 and ABD=2in^2. Determine the vertical displacement of end A and the displacement of B relative to C. 1.5 ft 8 kip 8 kip| C 1 ft D
2. The A-36 steel Bar BC had a diameter of 40 mm before the two loads, P, were applied. If after loading, the new diameter of the bar is 39.995 mm, what was P? P -1 m B 0.75 m 1 m
pon 9.18 A steel rodin. in diameter and 25 ft long is subjected to an ace axial tensile load of 15,000 lb. Compute (a) stress ons Lanogsib & new (b) strain (c) total elongation aaste sviesiqmos srit nimmst gaites 900 viss srit .rwoda al
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Consider a fillet sample subjected to a tensile force F while fixed to two 13-mm dia. bolts. Tensile failure will be observed at the portion where the stresses exceeded the elastic limit. Assuming uniform thickness, determine where the plastic behavior (behavior when the fibers exceeded the elastic limit) first occurred. a. Near one of the bolts b.40-mm section c.Near both bolts Tensile Force d.25-mm section Which of the following equations will give the maximum axial deformation for the member shown fixed at end A? PB Pc B A A PABLAB B. PABLAB AABEAB C. PARLAR D PcLac AnCEnC 40 mm- ←25 mm- PBCLBC + AABEAB ABC EBC PCLBC + AABEAB AncEnc 13 mm bolt C
1
Chapter 5, Reserve Problem 026 A solid aluminum [E = 70 GPa; a = 22.5 x 106/°C] rod (1) is connected to a solid bronze [E = 100 GPa; a = 16.9 x 106joc] rod (2)vat flange B as shown. Aluminum rod (1) has an outside diameter of 58 mm, and bronze rod (2) has an outside diameter of 110 mm. The bars are unstressed when the structure is assembled at 30°C. After the 300-kN load is applied to flange B, the temperature increases to 45°C. Determine the normal force in rod (1). 150 kN (2) (1) 150 kN 2.6 m O 40.1kN (C) O 62.2kN (C) O 54.0kN (C) O 49.0kN (C) O 74.3kN (C)
A steel beam is welded at the left and loaded as shown below. It has a rectangular cross section (height=h, thickness=t) with L=1m, a=0.4 m, h=3 cm, t=1 cm, F=500 N, w=200 N/m. a. Find the factor of safety if the material is 1020 Steel that has been hot rolled (hint: ductile) using an appropriate failure theory b. Find the factor of safety if the beam is the materials is gray cast iron number 50 (hint: brittle) using an appropriate failure theory. а F W
please do it as soon as possible it's a request
Q-2 The rotating shaft running at n = 900 rpm, shown in the figure below, is machined from AISI 1045 CD steel. It is subjected to a force of F = 10.1 kN. The shaft is experiencing an operating temperature of 35 oC. With the specified loading and for a reliability of 99.9 %, a) Determine the minimum factor of safety for fatigue based on infinite life*. b) Determine the maximum safe load (Fmax) that can be applied for a factor of safety of 1.5 and a design life of 5x105 cycles, all other input values remaining the same. c) Determine factor of safety against yielding. *Free-body, shear-force and bending moment diagrams are required.