AB and CD are two uniform and identical bars of mass 10 kg each, as shown. The hinges at A and Bare frictionless. The assembly is released from rest and motion occurs in the vertical plane. At the instant that the hinge B passes the point B, the angle between the two bars will be

AB and CD are two uniform and identical bars of mass 10 kg each, as shown. The hinges at A and Bare frictionless. The assembly is released from rest and motion occurs in the vertical plane. At the instant that the hinge B passes the point B, the angle between the two bars will be

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: As part of a test, the two aircraft engines are revved up and the propeller pitches are adjusted so…

A: The couple of the applied force is

Q: Two wheels weight W kg and 20kg respectively are connected by a rod of negligible weight and are…

A: According to Lamis Theorem, whenever at a point three forces are acting then the ratio of force upon…

Q: The 200MM Y 1.2KG connecting rod and the 1.5kg P piston are connected through the mechanism shown.…

A: Given data: The length of the connecting rod is, l=200 mm. The length of the crank is, b=90 mm. The…

Q: As part of a test, the two aircraft engines are revved up and the propeller pitches are adjusted so…

Q: If either a simple or a compound pendulum is used to determine experimentally the acceleration of…

A: Acceleration of gravity = g Mass center = G To proof That the period of oscillation τ obtained is…

Q: A car moving on a level road at a speed of 60 km/hr has wheel base 2.76 metres, distance of C.G.…

A: Given data as per the question speed=60 kmhr=1667 mswheel base (l)=2.76 mdistance of CG from…

Q: A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: Derive the equations of motion of the block of mass m1 in terms of its displacement x. Surface…

A: Given, a block of mass m1, Mass of the cylinder is m2, Radius of the cylinder is R, Distance between…

Q: L 15° 30 A uniform bar of mass 166.93 kg and length L=2.1 m is supported by two massless…

A: Given: Mass of the bar is 166.93 kg. Length of the bar is 2.1 m.

Q: Gear A has a mass of 1 kg and a radius of gyration of 30 mm; gear B has a mass of 4 kg and a radius…

A: Write the given data:

Q: The sliding glass door rolls on the two small lower wheels A and B. Under normal conditions the…

Q: Identify the type of ensuing motion of the discs and draw the free body, kinematic and kinetic…

A: Type of ensuing motion:The ensuing motion of the discs will be a combined rotation about point A and…

Q: The pendulum consists of a 35-lb sphere R-0.6 ft, and a 14-lb slender rod a-13 ft. Just after the…

A: Mrod=14-lb = 0.435133 slugsa=1.3 ft R=0.6 ftMsp=35-lb =1.08783 slugsParallel axis…

Q: The crank OA rotates in the vertical plane with a constant clockwise angular velocity ?0 of 4.9…

Q: Wheel A, of 30kg, is located in the position shown by the effect of idler wheel D (frictionless…

Q: 15. The set of four rollers shown has fixed axles and transfers rotation from each roller to the…

Q: A circular rigid disk of mass m kg and radius rm is stationary at the top of a fixed sphere of…

A: Given: Disk mass - mDisk radius - rSphere radius - 2r To find: Angle θ at which the disk leaves the…

Q: A ball of mass m and radius r rolls along an inclined plane for which the coefficient of static…

Q: Determine the equivalent of the system using the linear motion of the thin disk 2k Slender bar of…

Q: A 4 lb unbalanced wheel is rolling without slipping on a horizontal surface with an angular velocity…

Q: See figure of exercise 16.121. If the motion is caused by a horizontal force F acting at point O,…

A: Given: To find: Force F

Q: Derive an expression to find the normal reactions at the front and rear wheels considering the…

A: To find out :-Derive an expression to find the normal reactions at the front and rear wheels…

Q: B bar, negligible weight movement on the surface indicated by the wheels is doing. The bar is at…

Q: A shaft carries four masses A, B, C and D of magnitude 10 kg, 20 kg, 15 kg and 25 kg respectively…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Here, the given v0=0 I=mk2a=αrβ=10° To Find: The clear distance , after 5.8 s of motion between the…

Q: The figure (not to scale) shows a representation of a hoisting system. A couple is applied to the…

A: Initial angular velocity of A, Final angular velocity of A, Time interval

Q: As part of a test, the two aircraft engines are revved up and the propeller pitches are adjusted so…

Q: r the position shown, the assembly of two identical iform rigid bars, each with a mass m and length…

A: Given,

Q: The boom on a 6300kg truck is used to unload a pallet of shingles of weight 7750kg . Determine the…

A: The weight of the boom is - WB = 6300×9.81 = 61.80 kN The weight of pallet of shingles is - WS =…

Q: The force P is applied to the 40-kg block when it is at rest. Determine the magnitude and direction…

Q: Problem 2.2: The 20-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the…

Q: 6m 15° A B -0,5 m

Q: Three 25-lb rotor disks are attached to a shaft that rotates at 720 rpm. Disk A is attached…

A: The system is dynamically balanced if the effective forces are equivalent to zero. Let Points…

Q: 1 kg 30° B A 500 mm

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

AB and CD are two uniform and identical bars of
mass 10 kg each, as shown. The hinges at A and
Bare frictionless. The assembly is released from
rest and motion occurs in the vertical plane. At
the instant that the hinge B passes the point B,
the angle between the two bars will be
-1 m
30°
B.
A
0°
3.
0.5 m
0.5 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Diagram

VIEW

Step 3: FBD and Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Pravinbhai
the proel governor shown as each ball weighs 3 kg and central sleeve weight is 25 kg. The arms are of 20 cm length and pivoted about axes displaced from central axis of rotation by 3.75 cm, y = 23.8 cm, x = 30 35 cm, CE = 8.5 cm, MD = 14.25 cm. Determine equilibrium speed.
Pravinbhai
A uniform disc of 25-kg mass and 500-mm diameter is mounted on a shaft. The plane of the disc is not perfectly at right angles to the axis of the shaft but has an error of 2.5 deree. Determine the gyroscopic couple acting on the bearing if the shaft rotates at 1000 rpm.
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A uniform 4-kg cylinder A, of radius r= 150 mm, has an angular velocity wo = 52 rad/s when it is brought into contact with an identical cylinder B, which is at rest. The coefficient of kinetic friction at the contact point Dis uk. After a period of slipping, the cylinders attain constant angular velocities of equal magnitude and opposite direction at the same time. Consider that cylinder A executes three revolutions before it attains one revolution before it attains a constant angular velocity. constant angular velocity and cylinder Bexecutes Determine the final angular velocity of each cylinder. The final angular velocities of cylinders A and B are |rad/s (Click to select) and rad/s (Click to select) + , respectively.
Please answer quickly! Thanks
A garage door is mountedon an overhead rail (Fig.).The wheels at A and B have rustedso that they do not roll, but ratherslide along the track. The coefficientof kinetic friction is 0.52. The distancebetween the wheels is 2.00 m,and each is 0.50 m from the verticalsides of the door. The door is uniformand weighs 950 N. It is pushedto the left at constant speed by a horizontalforce F S , that is applied as shown in the figure. (a) If the distanceh is 1.60 m, what is the vertical component of the force exerted on eachwheel by the track? (b) Find the maximum value h can have withoutcausing one wheel to leave the track.
Solve it correctly. I ll rate
A Hartnell type spring loaded governor rotates about a vertical axis. The two rotating masses weigh 10 N each rotate at a radius of 130 mm when the speed is 600 r.p.m. At this speed the arms, which are vertical and horizontal, have effective lengths of 110 mm and 80 mm respectively. The equilibrium sped is 630 r.p.m when the rotating masses are at their maximum radius of 160 mm. Determine the stiffness rate of spring, the compression of spring at 600 r.p.m.
Part A The 21-kg roll of paper has a radius of gyration kA = 90 mm about an axis passing through point A. It is pin supported at both ends by two brackets AB. The roll rests against a wall for which the coefficient of kinetic friction is u = 0.2. Neglect the mass of paper that is removed. (Figure 1) Determine the magnitude of the constant vertical force F that must be applied to the roll to pull off 1 m of paper in t = 3 s starting from rest. Express your answer to three significant figures and include the appropriate units. TH HẢ ? F = Value Units Submit Request Answer Provide Feedback Figure < 1 of 1 300 mm 125 mm