A2Neglecting all frictionallosses, find the velocity (V) of the airentering the horizontal venturi tube1.2 kg/m³)=0.5A1Alshown. (Pair(a) 23 m/s (b) 26 m/s (c) 28 m/s(d) 21 m/s10amProblem (6)water

Given data: ρair=1.2 kg/m3A2A1=0.5 Need to determine the velocity of the air entering the horizontal…

A2 Neglecting all frictional losses, find the velocity (V) of the air entering the horizontal venturi tube shown. (Pair = 1.2 kg/m³) V A2 = 0.5 A1 %3D Al (a) 23 m/s (b) 26 m/s (c) 28 m/s (d) 21 m/s 10am Problem (6) water

A2 Neglecting all frictional losses, find the velocity (V) of the air entering the horizontal venturi tube shown. (Pair = 1.2 kg/m³) V A2 = 0.5 A1 %3D Al (a) 23 m/s (b) 26 m/s (c) 28 m/s (d) 21 m/s 10am Problem (6) water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A circular pipe of I.D. 4 m is bifurcated into two pipes of I.D. 2 m each. If the average velocity of water flowing through the main pipe is 5 m/s, then the average velocity through the bifurcated pipe is
Read the question carefully and give me right solution according to the question
Please don't copy from other site.
PROBLEM 5: In Lake Geneva (Switzerland), there is a water jet (called the Jet d’Eau) that is discharged 130 m straight upward (measured from the surface of the lake). The exit of the discharge pipe is 20 cm in diameter.
Fast pls i will give u like for sure solve this question correctly in 5 min pls A reduced bend in a pipe is used to divert the flow of water (p=1000 kg/m³) at a rate of 35 kg/s. The discharge of the fluid is to the atmosphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the outlet. The elevation difference between the centers of the exit and entrance is 40 cm. The mass of the cubit and the water it contains is 60 kg. The center of mass of the fluid assembly and elbow is located 50cm horizontally, with respect to the flange. Consider a flow correction factor of n=1.04 for eq. of linear momentum. Determine: a. The pressure at the entrance of the elbow. b. The net anchorage force in the flange required to hold the elbow in place. c. The moment generated in the flange from the applied forces
A pump with a 25 cmrev and 1000 rpm supplies the following circuit. If the characteristios of the Sokg cylinder are v-0.1 ms, piston diameter60mm, rod diameter-25mm and friction factoe-2000 Ns/m and the characteristics of the 100kg cylinder are v0.02 m/s, piston diamcter-40mum, rod diameter-30mm and friction factor-s00 Nsim. Determine the flow rate and pressiare on cach cylinder. 25cm 100 kg lo aorem Boky v.0.1 Piston 6e
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N. How many hp is needed for the pump to function if its efficiency is just 80%?
4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the turbine, at the inlet, with the velocity Vin = 40m/s and the mass flow rate m=1,000kg/s. Water exits the Vi,z40ms turbine with a negligible velocity, say, Vout = 0 m/s.The efficiency of m - loooly/s Figure on the right shows a hydraulic turbine designed HzO HzO the turbine is 75 %. Potential energy and flow work can be ignored. 4а. Please calculate the specific kinetic energy of water entering the turbine ( ɛr or ke; in J/kg). 4b. Please calculate the rate of total kinetic energy of the water flow ( É̟ or KĖ ; in J/s or W) 4с. Please determine the mechanical power output of this turbine (Wou; in W or kW). 4d. Please determine how much mechanical energy would this turbine generate during an hour
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
B4. An orifice meter with orifice area 1072 mm2 is inserted in a pipe of area 2144 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 75 cm of mercury. Find the rate of flow of oil of sp. gr. 0.85 when the co-efficient of discharge of the orifice meter = 0.6. Head of water (in m) The discharge of water through pipe (in Litres/sec)
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74 m B. 2.56 C. -2.72 m D. -4.67 m