A. Understanding resistor values 1. Pick 2 resistors. Compute resistance using the color table presented in figure 1. 2. Now measure the resistance using the voltmeter. 3. Fill the table below. Show any one calculation to your teaching assistant.

A. Understanding resistor values 1. Pick 2 resistors. Compute resistance using the color table presented in figure 1. 2. Now measure the resistance using the voltmeter. 3. Fill the table below. Show any one calculation to your teaching assistant.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Report 5. Five resistors (2 ohms, 4 ohms, 6 ohms, 8 ohms, and 10 ohms) are connected in parallel. Determine the current in 10-ohm resistor if the current in the 2-ohm resistor is 1 ampere. O a. 0.2 amperes O b. 2 amperes O c. 20 amperes O d. Not enough information
The heating element of a simple heater consists of a 2.0-m-long, 0.60-mm-diameter nichrome wire. When plugged into a 120 V outlet, the heater draws 8.0 A of current when hot.a. What is the wire’s resistance when it is hot?b. Use your answer to part a to calculate the resistivity of nichrome in this situation. Why is it not the same as the value of ρ given for nichrome in the given table?
2. Three resistors of 50 0, 100 and an unknown resistance R are connected in parallel and the combination is connected to a 25 V source. If the total current delivered by the source is 1 A, detemine the following A. The value of R B. The current in each resistor C. Which resistor dissipates the highest power? Show your solution.
3. Use the table of values in SSLM week6, p3. Calculate the resistance of copper wire, 100m length, 1.0mm diameter a. circular cross section (in Ohms). B. Having same resistance in (a), what would be the length of aluminum made, 1.0mm diameter-circular cross section (in m)? b. C. If the copper wire in (a) was replaced by steel material, having the samne length of 100m, what is diameter of a circular cross section wire (in m)?
7. Two identical 50 resistors and a 100 resistor are connected in a circuit. Which of the following cannot be the effective resistance of these resistors? A. 20 Ω Β. 12.5 Ω C. 8.3 D. 17.5
If three resistors connected in series to a battery. Suppose R1 carries a current of 22.5A, R2 has a resistance of 150, and R3 dissipates 60W of power. What is the voltage across R3 and Resistance of R3 ? 1. Voltage across R3 %3D and 2. Resistance of R3 =
8. A student is investigating how the resistance of a lamp changes with the amount of current flowing through it. The following equipment is available: wires, a 12 V battery, a variable resistor, a filament lamp, an ammeter and a voltmeter. a. How could these components be used to take measurements of the potential difference across the lamp for different currents? Use a circuit diagram in your explanation The student's results are show in the graph below. Voltage - Current Graph for a Filament Bulb 18 16 14 12 10 8 4 2 0.5 1 1.5 2 2.5 Current (A) b. What is the potential difference across the lamp when the current is 0.2 A? Potential Difference (V)
1. Including uncertainty, calculate the expected resistance of an orange-green-red-gold resistor. 2. A student wires a circuit. When the power supply is switched on, the ammeter reads I = 60 mA and the voltmeter reads V = 4.5 V.a) Use Ohm’s law to calculate the resistance of the resistor being measured.b) What should the student set the voltage to so the current in the resistor is 0.05 A? c) Assuming the resistor has a 10% tolerance, what the color code?
1. A resistor of unknown resistance is connected in series to a 3-ohm resistor. The voltmeter in the 3-ohm resistor registers 4 V and in the unknown one 6 V. What is the resistance of the unknown resistor? Draw the circuit diagram in the given part. 2. The voltage of a battery is found to be 4.2 volts. Two resistors of 2 and 4 ohms are connected in series to the battery. Then a single resistor of unknown resistance is connected in parallel with the two resistors. A current of 1.4 amperes is registered in the ammeter of the unknown resistor. What is the current in the 2-ohm resistor? What is the voltage in the 4-ohm resistor? Draw the circuit diagram in the given part.
4a. Find the current in the circuit (magnitude and direction). 4b. Find the potential difference of V_ab of point a with respect to point b. 4c. Find the potential difference of V_bc of point b with respect to point c. 4d. What is the totatl rate at which electrical energy is dissipate in R1, R2, and R3 resistors. 4e. What is the power output of the 26.0V battery? 4f. At what rate is the electrical energy being converted to other forms in the 10.0V battery? 4g. Show that power output of the 26.0V battery equals the overall rate of dissipation of electrical energt in the rest of the circuit?
1. Find the equivalent resistance between points a and b in the Figure. 2. If a potential difference of 12.0V is applied across a and b, what is the current through R2? 3. If a potential difference of 12.0V is applied across a and b, what is the potential difference across R2?
Problem 1. What is the equivalent resistance of the combination of resistors between points a and b in the figure? Note that one end of the vertical resistor is left fre.