a. Determine the magnitude of the projected component of the 100-lb force acting along the axis BC of the pipe. b. Determine the angle 0 between pipe segments BA and BC.

Q: 4. 40kN/m 210kN A E B D 8m 8m 4m 4m I I a. Using the force method draw the primary structure for the…

A:

Q: P kN В w kN/m 12 m A 5 m - 5 m Draw the schematic / blown-up diagram of the frame showing the member…

A:

Q: Water 18 radius

A:

Q: Determine the moment M in kN-m that must be applied to the beam to create maximum stress of 97 MPa.…

A:

Q: Determine the normal and shear stresses at point B.

A: Consider the figure,

Q: Hinge A Plate 1.2 m. F 1.2 m x 1.2 m) B 30 Container liquid

A: To find force on gate AB

Q: Specifications of the steel rod at B. L=2 meters diameter= 25 mm E= 200 GPa Show complete…

A: Given data L=2 meters diameter= 25 mm E= 200 GPa

Q: C F 2 m 2.5 m В 3 m A

A:

Q: Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of…

A: Solution:Given Data:The concentrated load acting on the beam is P=5kipThe intensity of uniformly…

Q: Can you explain in detal why the moment about x is -0.450(150)? from my point of view it should be…

A: See the explanation given below. Explanation:Step 1: Step 2: Step 3: Step 4:

Q: Find the diameter of the shaft required to transmit 60 kW at 150 rpm if the maximum torque exceeds…

A:

Q: 2.21 The rigid bars ABC and CD are supported by pins at A and D and by a steel rod at B. There is a…

A:

Q: The pipe has an applied force of 2000 N. 5 m B F= 2000 N A 12 m 7 m y 3 m 10 m a. Express the 2000 N…

A: Given: The applied force is 2000 N. Consider the figure,

Q: The spool of wire having a weight of 300 lb rests on the ground at B and against the wall at A.…

A: Draw the free body diagram.

Q: Determine the couple moment acting on the pipe shown .Segment AB is directed 30° below the x–y…

A: The couple moment acting on the pipe will be same as calculated about any point. So let us consider…

Q: Analyze the beam below: 1 m Α.Δ. 400 kN/m 6 m 2 m 600 kN B 2 m (a) determine the maximum moment…

A:

Q: 6000mm 6000mm X kN ww A Y kN www 6000mm В C

A:

Q: The rectangular plate is subjected to a distributed load over its entire surface. The load is…

A: The volume of the differential element is given by,

Q: Three cables pull on the pipe such that they create a resultant force R. Two of the cables are…

A:

Q: force water. Determine the force & angle on gate AB.

A:

Q: I5 Jo KN A Im 6 m 2.5m 2.5m

A: To determine the resultant of all the forces acting on the beam, we need to calculate the total…

Q: The gate AB is 8 m wide. Determine the horizontal and vertical components of force acting on the pin…

A: The free body diagram of the gate is shown below.

Q: Three forces are applied to lever ABD. (a) Draw Mohr's Circle for Point H, (b) determine the max…

A: free body diagram at H Draw Bending stress diagram Shear stress diagram

Q: Determine the magnitude of the pin force at B. 0 0.43 m 0.61 m 125 N-m B 0.43 m 0.43 m

A: To find out the magnitude of the pin force at  B.

Q: 6000mm 6000mm X kN w A Y kN 6000mm В C

A:

Q: Determine the resultant internal normal force acting on the cross section through point B of the…

A:

Q: plate. If the forces are concurrent at point O, determine the magnitudes of F and T for equilibrium.…

A: For any system to be in equilibrium, equilibrium equations must be satisfied. Here the system has to…

Q: P kN В W kN/m 12 m A 5 m 5 m Draw the schematic / blown-up diagram of the frame showing the member…

A:

Q: Q1.Find the moment of the force about point O 20? F = 60 N 100 mm Q2. The force F acts on the end of…

A:

Q: 1. Determine the resultant internal loadings acting on the cross section at B of the pipe shown. End…

A:

Q: D, 3 Use the diagram shown above. Given • D= 10 ft • D2= 7 ft • D3=4 ft • W - 500 #/ft Solve for the…

A: Figure is as shown

Q: E = 200 GPa А 3 300 mm? L = 3 m | 50 kN 2 m 2 m A B D 3 m 1.5 m

A:

Q: Solve a and c

A: Given data : Shear force (V)=15 KNWidth (B)=40 mmDepth (D)=140 mm

Q: SHOW COMPLETE SOLUTION PLS  VALUES: A= 5 B = 5 C = 1 Y = 25

A:

Q: 1. If the angular velocity of link AB is wAB = 3 rad/s, determine the velocity of the block at Cand…

A:

Q: 55 kN 64 kN 100. kN/m D A B Im 3m Im R1 FIGURE A R2

A:

Q: 1. Determine the resultant internal loadings acting on the cross section at B of the pipe shown. End…

A: The rotating force torque is calculated because of the product of the force and also the moment of…

Q: A uniform distributed torque of 20 kNm/m is applied to the shaft which is fixed at A and C. G=7.5GPa…

A: It is required to determine the polar moment of inertia. J=π32D4-d4=π3280 mm4-60 mm4=2748894 mm4 We…

Q: 1.2.7

A: Step 1:Step 2: Step 3: Step 4:

Q: P kN В W kN/m 12 m A 5 m 5 m Draw the schematic / blown-up diagram of the frame showing the member…

A:

Q: ing signpost. The post is fixed t uniform pressure of 7 lb to the face of the sign. 3 ft

A:

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.