A column section shown is reinforced580 mmwith 4-28 mm diameter steel bars. If fc' =21 MPa and fy = 275 MPa, determine theff:a. Capacity of the columnb. Distance of the plastic centroid, iMoment due to the given load, Pu500c.300Pu=1200 kN656530020018 A column section shown is reinforced580 mmwith 4-28 mm diameter steel bars. If fc' =21 MPa and fy = 275 MPa, determine theff:a. Capacity of the columnb. Distance of the plastic centroid, iMoment due to the given load, Pu500c.300Pu=1200 kN656530020018

Column: - It is a vertical structure which is used to transmit compressive load from top of the…

Answered: a. Capacity of the column b. Distance…

Engineering

Civil Engineering

a. Capacity of the column b. Distance of the plastic centroid, i Moment due to the given load, Pu с.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure below shows a uniformly tapering bar of rectangular cross-section of length L and thickness t. The width of the bar at one end is b₁ and the width at the other end is b2, where (b₂> b₁). The bar is subjected to an axial force P. The axial deformation due to load P is given by _mm. b₂ PL atE b₁ = 20 mm b₂-40 mm -In () then the value of (a + c) is
Example 3.7 Determine the force developed in each member of the space truss and state if the members are in tension or compression. The crate has a weight of 5 kN. Z. -2 m. 2 m C 2 m B A 2 m
A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15900 ksi] rods, and a solid steel [E = 30300 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.69 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.42 in. Assume L=37 in and L2=68 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 28 kips is applied. (1) L2 (1) B P. Answers: i 27.744 ksi. 02 = 4.512 ksi.
solve correctly and show the complete solution.
Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E = 200 GPa 1 = 8 x 106mm Load = 2 kN A 5m B Using the following method: 2 KN + 2m + 2m |- You are tasked to analyze the continuous beam by calculating the: > the displacement on the beam at B and C and > the reaction at the supports Matrix Structural Analysis Use the following steps as a guide to analyze the beam: Matrix Structural Analysis ✓ Produce Notations ✓ Establish the known displacements and known external load ✓ Produce Member Stiffness Matrix ✓ Displacement and Load ✓ Calculating the displacement Calculating the reaction at the support
What is the value of the force in the member AB in N? if P = 60-N. (Note: enter your numeric answer only. No need to enter units. Give your answer to three decimal places and negative for compression). AB= -2 m D -2 m- E 1.5 m B.
7) The load P is located midway between points B and C. P = 1.7 kN. The diameter of the rod at CE is 4.8 mm. The young's modulus of the rod metal = 200 GPa. What is the elongation of the rod CE? 600 mm IB 600 mm 600 mm Elongation of rod EC = units
A rectangular beam is supported at both ends. It carries two concentrated load of 190KN, a clockwise moment of 160KN- m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 150GPA. Solve the following if the reaction at point B is 309.63888888889KN, upward. USE ANY МЕТНOD BEAM DIMENSION: Width = 130mm , %3D Height = 460mm %3D NOTE: b = 4.2m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) P W M 1m 1m 1m Determine the deflection at midspan
How to solve for the centroid of the composite body using the principle of moments and treat each part as a finite element of the whole figure (show a step by step solution)
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. 5P E-110 GPa 3P E=200 GPa 7m 3M 80mm 30 mm 30 mm 80 mm 30 mm 30 mm