A. Ammeter-Voltmeter MethodsDATA TABLE 1Purpose: To measure resistance values.29.3Voltmeter resistance RAccepted value of RDATA TABLE 224.6Purpose: To measure resistance values.RheostatCurrent Isetting Rh( )Voltage V( )Resistance R( )Rheostatsetting RhCurrent IVoltage VR' = V/I( )( )()1,011) A1.7601.0117A1.7582.0112 A1.6692.0113 A1.7003.0106 A 1.5923.0107A1.611Average RAverage R'Calculations(show work)Percent error of RPercent error of R'Ammeter resistance R3

Answered: Image /qna-images/answer/acd20895-ec4f-477b-8743-9c53503571b8.jpg

Answered: A. Ammeter-Voltmeter Methods DATA TABLE…

Similar questions

1. The numbers in the circuit below are the resistance of the resistor in ohms.A) Find the equivalent resistance of the circuit when the switch S is open (ReqO) and when the switch S is closed (ReqC)B) When the switch S is closed, the equivalent resistance drops to 90.0% of the original value. Determine the value of R.C) What would the voltage (in V) between points a and b have to be for 153.0 W to be delivered to the circuit when the switch is closed?
A. Compute for the total current of the circuit. The diagram below is a combination of series and parallel connection. B. Calculate the equivalent resistance of the circuit. C. Find the current in R1
If you have a 10 ohm resistor and 5 amp current going through a circuit, what is its voltage? Select one: O a. 0.2 V O b. 5.0 V O c. 2.0 V O d. 0.5 V
What is the total resistance of the circuit if R1= 20 ohms, R2= 60 ohms, R3=100 ohms, R4= 40 ohms a. 220 ohms b. 80.035 ohms c. 108.6 ohms d. none of the above
1. Construct a truth table for the figure.2. Obtain the MINTERM expression from the truth table.3. Draw the circuit diagram for the MINTERM expression
5. Refer to the circuit diagram below; calculate the total resistance, total current, voltage in each resistor, and current in each resistor. Total Resistance: Total Current: Voltage in R1: Voltage in R2: Voltage in R3: Vtotal: 6.00 V Current in R1: Current in R2: Current in R3: ELETC R1: 3.00 Q R2: 8.000 R3: 4.00 Q 000
Q1/ R1= 5 k ohm R2=15 k ohm R3= 20 k ohm R4= 10 k ohm R5= 20 k ohm I = 5 mA Find: a) I1 , I2 , I3 , and IT . b) Total Resistance of the circuit. c) The voltage (V) and Power supplied(P) by the battery.
1. Including uncertainty, calculate the expected resistance of an orange-green-red-gold resistor. 2. A student wires a circuit. When the power supply is switched on, the ammeter reads I = 60 mA and the voltmeter reads V = 4.5 V.a) Use Ohm’s law to calculate the resistance of the resistor being measured.b) What should the student set the voltage to so the current in the resistor is 0.05 A? c) Assuming the resistor has a 10% tolerance, what the color code?
5. Assume that you need to measure an average temperature in a heated space. You have three identical temperature sensors. Each sensor produces a voltage proportional to temperature such that: Sensor Voltage = .01 * Temperature in degrees Celsius Assume that you bave three voltages, Va, V, and V, You want to take the average of these three voltages lin order to compute the average temperature inside the heated space. This circuit has been suggested as a possibility for computing the average. Rf ww Vout A. Find an analytical expression for Vout in terms of the input voltages and the four resistors. B. Determine if a proper dhoice of resistors will let you use this as a averager. If you can, then find some appropriate values for the resistors.
1. The circuit shown is example of a? 2. According to Kirchoff's current rule, the current in point b is equal to the current in? 3. According to Kirchoff's current rule, the emf in the battery is equal to the potential difference measured between? 4. What is the total resistance in the circuit? 5. What is the total current in the circuit?
1. Use the following diagram to answer the questions below. a. What are the single resistor elements in series? b. Calculate the equivalent resistance of the circuit The voltage of the source is 90V 12.27A 20 10 20 30 ww 10 20 10 1.64A
1. Voltmeter is an electrical instrument used to measure potential difference or voltage. To get the measurement, it is connected in series 2. Voltage source and terminal voltage can be related as [Choose any one answer] 3. A constant current source supplies a electric current of 200 mA to a load of 2kO. When the load changed to 1000, the load current will be 4. Internal resistance of cell when there is current of 0.40A when a battery of 6.0V is connected to a resistor of 14.50 is ENG 4) G O A hp