a. A positive displacement, rotary vane type compressor is installed in a power plant. The air pressure increase occurs from 100 kPa to 200 kPa while the compressor compresses 4.5 m' of air per minute when operating at 500 r.p.m. You have to find the power required to drive the compressor when: 1. The parts are so placed that there is no internal compression. 2. The parts are so placed that there is 50% increase in pressure due to compression before the backflow occurs. b. Compression of air is performed while using a Roots blower compressor. The pressure of 0.1 m' air increases from 2 bar to 2.5 bar per revolution. Calculate the efficiency for this compressor.

Q: ng based on the degress scal from 0 to 72

A: 4 steps are present in the IC cycle. inlet compression power exhaust

Q: A set of sprockets is constructed, as shown in Figure 1, so that the second and third rotate on a…

A: Solution: Given Data: r1=1 cmr2=4 cmrc=1 cmr3=3 cmN1=y rpmN2=u rpmN3=x rpm   To Find: (a) N1N2(b)…

Q: The beam AB is homogeneous and has a mass of 5,191. The tension in the cable of the crane can not…

A:

Q: The velocity of the piston is 52.9901 3 ft/s.

A: use sine rule

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the y-axis (θy)? Note that…

A: The cosine angle between two vectors  is as followes,

Q: Briefly describe the action taken by the following G&M command blocks assuming absolute coordinates.…

A:

Q: where are the graphs?

A: Given data in the related question: Maximum speed = vf = 183.58 mi/hr Distance travelled = 5 mi Time…

Q: create 2 fourbar designs that include the dimensions and angle of motion

A: It is asked to draw four bar mechanism with given motion

Q: Give all the location dimensions between the datum target areas , A1 and A2. X = _________________,…

A: Give all the location dimensions between the datum target areas , A1 and A2.X =0  ,  Y =74   ,   Z =…

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Consider FIG-DD in the appendix.   Note: For Blocks “A” & “B” & “C”: The mass of “A” is 30 kg.…

A:

Q: Find the number of rotations of wheel 3 in rotations per minute (rpm) wile the load A is moving down…

A:

Q: a Show how Pip can complete the circuit by adding less than 120 cm of track. b Show how Pip can…

A:

Q: Use the image below to do the following  i.  draw 3 positions on a piece of paper. ii.  Chose a…

A: Find three positions and corresponding distances based on the reference point.Alos find linear…

Q: To convert an arc to a circle: a. Use the FILLET command with a 0 radius b. Use the EXTEND command…

A: JOIN:The JOIN command joins similar objects to form a single unbroken object. The JOIN command…

Q: The vertical distance above a reference datum to a point is called the point’s

A: ▪︎We have to specify the term related to the vertical distance above the reference datum to a point.…

Q: State any three rules of orthographic parallel projection.

A: Orthographic parallel projection is a method of representing 3D objects normally by three 2D…

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.