Answered: A Wx35 steel column has an unsupported…

A Wx35 steel column has an unsupported height of 6m. Use A36 steel with Fy = 248 MPa and E = 200,000 MPa. A = 6504 rx=88.9 mm ry = 51.56 mm Determine the safe axial load if both ends are hinged.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Select an A992 W-shape for beam AB of the floor system shown in Figure. In addition to the weight of…

A: Solution; Given that; Beam spacing=5ft, Span Length=30 ft, L.L=80psf, Partial Load=20psf

Q: Determine the effective length factor for column MN of the unbraced frame shown. The loads applied…

A: Column section MN = W12x96 Beam section = W18x46 Column length, L = 13 ft Beam length = 30 ft Dead…

Q: A simply supported beam with a span length of 48 feet is laterally supported at its ends and is…

A: Span of simply supported beam = 45 ftDead load = 400 lb/ftLive load = 1000 lb/ftSection of the beam…

Q: Situation 20. A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is…

A: Given, Ag = 14,968 mm2 rx = 133.65 mm ry = 77.47 mm

Q: 2. Determine the applicable value of Pu for the following braced frame. The beam is a W10x45…

Q: se Allowable Strength Design. Use A992 steel and select a W-shape for the following beam: •…

A: Given- Service dead load = 0.4 kips/ftService live load = 1.2 kips/ftdead load=10kiplive load=12…

Q: The beam shown in Figure is laterally braced only at the ends. The 30-kip load is a service live…

A: ASD is based on the conventional stress calculation of structure with respect to the allowable…

Q: Check the beam shown for compliance with the AISCS. Lateral support is provided only at the ends,…

A: Load=70 Sin =70*(4/5) =56 KN =12.58 kipsDead Load=30% of 12.58=3.78 kipsLive…

Q: The properties of the steel column are shown in the table. Yield strength of the column and base…

Q: by 늘 wo B 늘 C X

A: Given Data:Length L=6.3md=300mmbf=215mmtf=14mmtw=10mmIt is required calculate the largest intensity…

Q: For the composite shaft shown, the total twisting angle is the sum of the twisting angles of steel…

A: False The shafts are bonded together as a composite bar so they will have strain compatibility. As…

Q: 5m 3m 3m 3m 3m Solve for the safest factored load Pu the compression members AB and BC can carry in…

A: For W16x50 Area = 14.7 sq-inch Assuming A992 steel So, yield strength (fy) = 50 ksi So, Tmax =…

Q: A concrete circular column with a radius of 350mm has f'c-25 MPa and is braced against sidesway. The…

A: Critical load The critical load is the maximum load that may be applied without causing lateral…

Q: A W14 x 74 compression member carries a service loads of DL= 2,500 KN and LL= 300 KN. The column is…

A: It is required to determine the factored load using ASD method. Pu=DL+LL=2500 kN+300 kN=2800 kN The…

Q: A W section of A992 steel (E350 MPa and F₁= 450 MPa) is used to serve as a column 4.90 m long to…

A: Hi! Thank you for the question As per the honor code we are allowed to do only one question at a…

Q: Q2. Design the required tensile and compression rebars for the cross section shown below. Mu= 288…

A: for given cross section given b=250mm D=500mm MU=288KN-M FC=20 MPA FY=300MPA

Q: 3.3. Determine the maximum service live load that the column can support if the live load is twice…

A: Section C8×18.75 Calculate the moment of inertia about y-axis…

Q: Situation 3. A W12x81 is used as a column. The effective length in either principal direction is…

A: The question asks you to find the cutback width (labeled as 2.187) based on the given information.…

Q: A W21 x 68 of A992 steel is used as a simply supported beam with a span length of 50 feet. The only…

A: For section ,

Q: Determine the amplification factor for the following braced column (W21x44) (A992 steel). The…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: ad moments, and bend ad. K=K,= 1.0. Use LRF

A: (a) Calculate the factored axial compressive load. Here, is the dead load, is the live load.…

Q: A WT205 × 30 structural steel section (see Appendix B for cross-sectional properties) is used for a…

A: To Find a. Slenderness ratio b. Euler buckling load c. Axial stress in column Given data WT205×30…

Q: 3. Design a column of wide flange section W for the member (DE) of the frame shown below The frame…

A: Given data: Axial load on the column, P=2500 kN Effective length factor, Ky=1.0 and Kx=2 The column…

Q: For the flat plate shown in the figure below (edge beam are not used), design the hatched frame…

A: According to the question we have to design the middle and column strips of the hatched slab in N-S…

Q: The rigid frame shown is unbraced. The members are oriented so that bending is about the strong…

A: Given- Axial strength of column AB=?

Q: a. Which of the sections gives the largest allowable compressive strength? b. Which of the sections…

Q: AW14 x 53 of Grade 70 steel is used as a compression member. It is 30 feet long, pinned at the top…

Q: The rigid frame shown is unbraced. The members are oriented so that bending is about the strong…

A: Answer We need to first find G factors at Joint A and joint B in order to calculate 'Kx' GA = 1…

Q: For the column shown below, create an interaction diagram on Excel for bending about the strong axis…

Q: Find the moment of resistance of the section. The permissible stresses are 10 N/mm2 in tension and…

A: The values and diagram given in the question are as follows: The permissible stress in…

Q: A rectangular post (40 mm x 80 mm) made of wood, the length of which is 5 m, supports the BC beam.…

A: Consider the given data l=6 mh=5 mF.S=1.50ζy=2…

Q: A simply supported beam with a span length of 48 feet is laterally supported at its ends and s…

A: Span of simply supported beam = 45 ftDead load = 400 lb/ftLive load = 1000 lb/ftSection of the beam…

Q: A W14 x 74 compression member carries a service loads of DL= 2,500 KN and LL= 300 KN. The column is…

A: It is required to determine the factored load using ASD method.The properties of W14 x 74 areThe…

Question

A Wx35 steel column has an unsupported height of 6m. Use A36 steel with Fy = 248 MPa and E = 200,000 MPa.

A = 6504

rx=88.9 mm

ry = 51.56 mm

Determine the safe axial load if both ends are hinged.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q3) What are the techniques for retrofitting?
W 14 x 142 is used as a column having a length of 9 m. long. It is hinged at the r end and fixed at the lower end but there is a lateral bracing perpendicular to minor axis of the W section at a point 6 m. above the bottom support. It is assumed to be pinned connected at the bracing point. Using A 36 steel Fy 248 MPa the NSCP Specifications. E= 200000 MPa. Properties of W 14 x 142 A-26967.69 mm2 d=374.65 mm bf=393.70 mm tf-27.00 mm tw 17.27 mm Ix 695.11 x 106 mm4 Iy = 274.71 x 106 mm4 rx = 160.53 mm ry 100.84 mm 221 Assume: Kx=0.80 for 9 m. length KY 1.9 for the length on the upper support KY-0.80 for the length on the bottom support CIVIL ENGINEERING- STEEL DENON a) Compute the slenderness ratio along y-axis. b) Compute the slenderness ratio along x-axis. c) Compute the safe axial load
2. Determine the lightest W-shape for a column 30' tall in a braced frame. The column is braced at mid-height in the weak direction. The loads are 100k dead load and 200k live load. The bottom of the column is pinned and the top of the column is constrained in rotation.* Use A572 Grade 60 steel. *Not tronslation.
Determine the design moment capacity of the beam with given properties below. bf = 650mm bw = 350mm tf = 120mm d = 370mm d' = 100mm fc' = 34.5 MPa fy = 400 MPa As = 8 - 28mm bars USE NSCP 2015, Mu = kN-m
answer should be on the choices
Figure 1 shows the cross-section of a heavily welded I-section steel column under axial compression. The yield stress of the steel section is 300 MPa. (a) Check the slenderness of the flanges and webs. (b) Determine the effective and gross areas of the cross-section. (c) Determine the design axial capacity of the cross-section. 380 E 10 425 -8 Figure 1. Cross-section of the rectangular hollow section steel column (Units: mm)
Please Determine the axial load strength and moment (without and with reduction factor) a square columns for the following conditions and draw their interaction diagrams (note the scale): When conditions are in balance During the tensile condition When the pressure condition Pure axial Pure moment
Q3) The beam shown in Figure below has lateral support at the ends only. The concentrated loads are live loads. Use A992 steel and select a W shape. (Do not check deflections. Use C-1). 23 k 25 k ttst
Use A992 steel and select a W14 shape for an axially loaded column to meet the following specifications: The length is 22 feet, both ends are pinned, and there is bracing in the weak direction at a point 10 feet from the top. The service dead load is 142 kips, and the service live load is 356 kips. a. Use LRFD. b. Use ASD.
Select the lightest W section for the column shown in the accompanying figure. The loading is 30 kips dead load and 120 kips gravity live load. The member is built into a wall so that it may be considered as continuously braced in the weak direction. Note: Not all of the variable W sections are included in the AISC Manual "Available Strength in Axial Compression" tables. Use (a) A992 steel; (b) Fy = 60 ksi