Answered: A wrench is used to tighten a nut. A 15…

A wrench is used to tighten a nut. A 15 Newton force is applied 9 centimeters from the axis of rotation. What is the torque generated? 58 N m ) 0.58 N . m O 1.71 N m 1.35 N m 14 N m

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: What is the magnitude of the torque about the elbow by the weight of the forearm with hand, in N·m?

A: Torque is equal to the product of force and the distance of force from the rotating axis.

Q: An object is located on the x-axis, on the right of the origin. A force acts on it in the -z…

Q: A bar on its hinges starts from rest and rotates with angular acceleration of a=0.10 rad/s/s. During…

A: Given data: Angular acceleration, α=0.10 rad/sec2 Time, t=10 s Our question is to find the angle θ

Q: A wrench of length X cm is used to loosen a nut attached to a bolt. If a perpendicular force F…

A: Step 1: first we have to find out the equation of torque.Torque=r×F. Step 2: as force is constant…

Q: A gorilla has an arm that is 0.576 m long as measured from her shoulder joint to her hand. With her…

A: The equation for the magnitude of the torque is given by,

Q: A force F = (i+2j+3k)N acts at a point (4i + 3j-k) m. Then the magnitude of torque about the point…

Q: A 10 kg, 0.5 m radius wheel rotates with an angular acceleration of 10 rad/s/s. What is the…

A: Given: Mass of wheel, M=10 kg Radius of wheel, r=0.5 m Angular acceleration, α=10 rad/s2 To…

Q: A 1800 kg solid disc with radius 0.3 m is at rest when a 140_m-N torque is applied to the wheel. How…

A: Given: mass of solid disc, M = 1800 kg radius of disc, R = 0.3 m Torque applied, τ = 140 Nm initial…

Q: Calculate the torque about the z-axis that is out of the page at the origin in the following figure,…

A: Given Force, F1=3.10N,F2=1.90N, F3=3.00N,F4=1.80N Distance of each force, r1=3.1m, r2=2.2m,r3=0m,…

Q: A uniform door weighs 58.0 N and is 1.40 m wide and 2.60 m high. What is the magnitude of the torque…

A: Given, Width of the door = 1.4 m height of the door = 2.6 m weight of the door = 58N we need to…

Q: The diagram below shows a 400 N man balancing a boy on a teeter-totter. Ignoring the weight of the…

A: An object is said to be in rotational equilibrium when its rotational velocity is constant. This is…

Q: A Force F = (i+2j) N is acting on a point with position vector r= (2i-4j)m. What is the…

Q: A hamster sits 0.10 m from the center of a lazy Susan of negligible mass. The wheel has an angular…

A: distance, r = 0.1 m , angular velocity, ω = 1 rev/s distance, r' = 0.3 m

Q: A uniform solid sphere of radius 2.0 m and mass 10.0 kg is free to rotate about an axis through its…

Q: A constant tangential force of magnitude 1.5 N acts on the edge of a wheel. The wheel's radius is…

A: Given, Force F =1.5 N Radius R =0.20 m

Q: A figure skater is spinning with her arms extended. She now pulls her arms close to her body. What…

A: According to the law of conservation of angular momentum, the angular momentum of the skater must be…

Q: According to conservation of angular momentum, if the moment of inertia of a rotating object is…

A: Write the equation for the angular momentum. L=Iω ........ (1) Here, The linear momentum of the…

Q: 23 N 90° A 6.4 m What is the torque acting on the 6.4 m bar 'AB' shown above because of the 23 N…

A: Given data: Distance (r) = 6.4 m Force (F) = 23 N Angle (θ) = 90° Required: Torque (τ)

Q: How is Torque differentiate to a Moment? O Moment causes an object to obtain angular acceleration O…

Q: Based from Figure 1, determine W2 and the Net Torque W2 is 13 g and the net torque is 0.002 Nm W2 is…

A: Conditions for a system to be in equilibrium 1. Net force is zero. 2. Net torque is zero

Q: A E 300 P 50 D 2m 2m 4m 4m if A = B = C = D = E = F = 1ON Find the net torque at point p.

A: The torque at a point is defined as the cross product of the displacement vector and the force…

Q: Which of the following will result in the largest torque being applied to a door on hinges? The door…

A: Introduction: Torque is defined as the product of magnitude of force and the distance perpendicular…

Q: A moment of 15 ft-lbs is required to cut a thread on the end of a pipe. If the handles on the die…

A: We can calculate the required force by using the equation of torque

Q: A merry-go-round accelerates from rest to 0.68 rad/s in 33 s. If its moment of inertia is 750 kg m2,…

Q: What is the velocity of a point on the rim of a disk that has a moment of inertia of 0.5 kg-m2 and a…

Q: 8. A wheel turns freely on an axle at the center. Which one of the forces shown in the figure will…

Q: PHY210: TUTORIAL 2 (WEEK 3) What is the sum of all the torques at point D in figure below? 30N 10cm…

Q: The figure shows a lower leg being exercised. It has a 49-N weight attached to the foot and is…

Q: A truck wheel with radius R= 500 cm has an initial angular velocity of 12 rad/s, and is slowing down…

A: The final angular velocity is zero. The wheel is decelerating. Let, R=500 cm=5.0 mωi=12 rad/sωf=0…

Q: Assignment 3 1. 30 N - 30 N 5.0 5.0 ст cm 20 N 20 N The 20-cm-diameter disk can rotate on an axle…

A: Introduction: Torque is a twisting force that is responsible for the rotation of object, and torque…

Q: A cylinder of radius R = 20 cm is moving between two planks as shown in figure. There is no slipping…

A: Given:- A cylinder with the radius of R = 20 cm = 0.2 m There is no slipping at any point. Find:-…

Q: 12.0 N 30.0% b 10.0 N 9.00 N The figure shows one cylinder inside another. The inner cylinder has a…

A: Given: mass of inner cylinder, ma=2 kg mass of inner cylinder, ra=0.5 m radius of outer cylinder,…

Q: What is the net torque on the bar shown in the figure, about the axis indicated by the dot? Suppose…

Q: 10 kg m3= 1.0 m M-30 kg Mg Consider a 10 kg solid cylindrical drum with radius 1 m rotating about…

A: Solution: As given that mass of the cylinder m =10 kg radius r = 1 m mass attached M = 30 kg

Q: A wheel on a shaft is initially at rest, when a motor starts to supply constant torque. The wheel…

A: Rotational inertia I = 20.4 Kg m2 No of revolutions N = 3 full revolutions…

Q: The 22-cm-diameter disk pictured can rotate on an axle through its center. What is the net torque…

Q: block is pivoted about its center. A 5.0 N force is applied 4.0 m from the center and nother at 2.0…

Q: A tire rotates at an angular velocity of 40 rad/s. What angular displacement will the tire undergo…

Q: A 2 m steel rod is hinged as shown. The net torque (in N.m) exerted by the two forces on the rod…

A: It is required to find the net torque due to the forces. For this, it is required to calculate the…

Q: The body in the figure is pivoted at O, and two forces act on it as shown. If r₁ = 1.01 m, r₂ = 3.04…

Q: A rotating disk with an angular velocity of 3 rev/s is brought to rest in 12 seconds by a constant…

Q: What mass (in grams) would you hang on the right side of the system in the following figure to…

A: Answer:100kg

Concept explainers

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.

Question

A wrench is used to tighten a nut. A 15 Newton force is applied 9 centimeters from
the axis of rotation. What is the torque generated?
58 N m
O 0.58 N m
O 1.71 N m
1.35 N m
14 N m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

The graph below is for a 30 kg.m2 object. a) Find the net torque. b) Find the angular displacement at t = 3.5 s
A downward 8.7 N force (F1) is applied 2 m from the left end of an object. An upward force (F2) is applied 3 m from the left end. To keep the object from rotating, what is the value of F2?
Calculate the net torque on the disk of diameter 0.350 m with respect to an axis passing through the center as shown in the figure. The 11.9 N force is perpendicular to the edge of the disk, while the 8.50 N force is tangent to the disk. 11.9 N 40.0° 14.6 N 8.50 N O 6.26 N.m O 5N.m O 4.5 N.m O 24 N.m 0.350 m
A force of 3N is applied in the positive y direction and 5.5N in the negative z direction in a situation with a lever arm of 2.7m in the -x direction. What is the magnitude of the torque?
Which force produces the largest torque? O 20.0 N perpendicular to the center of rotation at a radius of 0.5 m O 20.0 N perpendicular to the center of rotation at a radius of 1.0 m 10.0 N perpendicular to the center of rotation at a radius of 0.25 m 10.0 N perpendicular to the center of rotation at a radius of 1.5 m
You are turning off a switch by applying 5N force, 1 centimeter away from the point of rotation. Considering that the direction of the rotation is clockwise, how much torque was created? O 5.0 x 10^ -2 Nm O 5.0 x 10^ -1 Nm O 5.0 x 10^ 1 Nm 5.0 x 10^ 2 Nm O Correct answer not found
If a person pushed on a door with a force of 60 N, and the moment arm was 1 meter, what would be the torque? 60Nm 90Nm 30Nm 0Nm
A wrench has five equal forces V, W, X, Y, and Z applied to it. Which two forces produce the same clockwise torque?
When opening a door, you push on it perpendicularly with a force of 67.5 N at a distance of 0.775 m from the hinges. What torque, in newton meters, are you exerting relative to the hinges?
12.0 N 30.0% b 10.0 N 9.00 N The figure shows one cylinder inside another. The inner cylinder has a radius of a = 0.5 m and a mass of 2 kg. The outer cylinder has a radius b = 1.5 m and a mass of 12 kg. On the system act 4 forces. Those shown in figure 2 and a friction force. If the magnitude of the frictional torque is 1.75 mN. Determine: a. The net torque vector on the system. (Magnitude and direction) b. The total moment of inertia of the system
true or false?
A hollow disk with a moment of inertia of 0.5 kg-m2 experiences a net torque of 30 m-N. What is the disk's angular acceleration? 60 rad/s/s 0.02 rad/s/s 30 rad/s/s 15 rad/s/s