A wooden block of mass 40 kg resting on an inclined plane is pulled upward by a force parallel to the plane. The plane is inclined at 13° with the horizontal. Coefficient of friction between the plane and the block is 0.16. Determine the force required to start the motion of the block on the plane.

A wooden block of mass 40 kg resting on an inclined plane is pulled upward by a force parallel to the plane. The plane is inclined at 13° with the horizontal. Coefficient of friction between the plane and the block is 0.16. Determine the force required to start the motion of the block on the plane.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A heavy cask (full of wine!) sits on an inclined plane. It is held in place by a rope that is attached to the cask and to a hook further up the inclined plane (at A). The rope comes off of the cask tangent to the cask. The mass of the cask is 40 kg, and the coefficient of static friction between the inclined plane and the cask is 0.25. What is the maximum value of θ just before the cask begins to slip? Also, what is the tension in the rope when slipping is impending? Finally, if the inclined plane became icy, and the rope didn’t break as the cask slipped, what would be remarkable about the lines of action of the W, N and T force vectors once equilibrium was re-established?
2. Compute the horizontal force P required to prevent the block from sliding down the plane for the 100 lb block shown. Assume the coefficient of static friction to be 0.65. 30° W = 100 lb MRSM
A ladder of length 2L and mass M is positioned on level ground leaning against a wall such that the angle between the ladder and the horizontal is @. The coefficient of static friction between the ladder and the wall and between the ladder and the ground is jistatic = 0.66. The centre of mass ofthe ladder is halfway along it. For the ladder to be in mechanical equilibrium: Write down equations for the total r- and y-components of the 5 forces acting on the ladder
The uniform 4.9-m pole has a mass of 230 kg and is supported as shown. Calculate the force P required to move the pole if the coefficient of static friction for each contact location is 0.28.
A 600-lb safe rolls on four 2-in.-diameter steel wheels. The wheels rotate on 1/4 in.-diameter axles. If the coefficient of friction between the wheel and the axle is 0.45, determine the force necessary to push the safe and the ratio of the rolling friction to the axle friction.
Determine value of force to remain the figure at rest
A ladder, 8 m long and having a mass of 25 kg, rests on a horizontal floor and is supported by a vertical wall. The ladder is inclined 62°, as shown, and starts to slip when a person having a mass of 73 kg has climbed halfway up it. The coefficient of friction at the wall is 0.20. Assume the weight of the ladder to be concentrated at its midpoint. Calculate the coefficient of friction at the floor. - Draw a free-body diagram - Solve most simple way
Kindly do not make any mistake.
A cube with mass of m=80N is on the inclined plane with angle of phi=20 degrees. coeficient of static friction /mu_s = 0.25 coeficient of dynamic friction /mu_k = 0.15 Determine: what is the smallest size of the force F parallel to the inclined plane, which prevents the cube in the slide? what is the smallest size of the force F, which the cube starts to move along the inclined plane up? At what value of the force F starts the cube to rise at a constant speed?
A screw jack is used to lift a load of 30 kN. The screw of the screw jack is square threaded with two threads of 1.2 cm. If the coefficient of friction between the nut and screw is 0.09 and the outer diameter of the screw is 6 cm, find the force required at the end of the handle of length 60 cm to lift that load.
Answer the picture below.
A uniform ladder of length L and weight w is leaning against a vertical wall. The coefficient of static friction between the ladder and the floor is the same as that between the ladder and the wall. If the coefficient of static friction is 0.360, determine the smallest angle the ladder can make with the floor without slipping.