A wire of length 50 is to be cut into two pieces, one peing bent to form a square and the other to form a circle. How should the wire be cut if the sum of the areas enclosed by the two ? pieces is to be minimum

Q: 6 - From the question (5) find the real length of the line AB. *

A: the real length of line AB

Q: Find the Shear Moment Diagram of the following problems using

A:

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Write the mathematical expression for the Brinell hardness test. HB=2PπDD-D2-d2 Here, Applied load…

Q: 8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of…

A: Answer: The elongation of the bar will be  ◆ When 30mm × 30mm square section : 2.22 mm. ◆ When 40mm…

Q: Problem 2: The stresses shown act at a point on the free surface off a stressed body. a) Determine…

A:

Q: The pressure is the highest pressure possible in the flow, if elevation changes are neglected.…

A: The stagnation or total pressure is the pressure measured at the point where the liquid comes to…

Q: Find the centroid of the shaded portion as shown in figure. Where b1 =85 mm, d %3D

A:

Q: Problem 3 A gate is 1.5m in width and hinged at point A. Another point on the gate, B, is resting…

A:

Q: A construction vehicle has a diesel engine with 8 cylinders of 5.375in bore and 8in stroke,…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: nd the Zero member enlys 3 3. 3. D. 3. 3. 8m

A: given; find zero force member only

Q: f the crankshaft in the sliding mechanism below has a uniform angular velocity o 1800rpm. Determine…

A: GivenNBO=1800rpmO2B=63.5BC=152

Q: The distance y from the back of the shorter leg to the neutral axis XX is

A:

Q: For a certain interval of motion the pin A is forced to move in the fixed parabolic slot by the…

A:

Q: BOX ONLY REQUIRED ANSWER AND PRESENT IN 4 DECIMAL PLACES. For the shaded region, determine the…

A:

Q: Consider the schematic of a riveted lap join subjected to tensile load F, as shown below. Le d be…

A: TO determine the minimum value for the thickness of the plates.

Q: O lit/sec water enters a centr ally at 5 m/s and leaves at a - axial direction. If the inlet

A:

Q: A vertical pole consists of two parts, each one half of the whole pole. At a point in the horizontal…

A: Given: tangent by upper half = 1/3 base = 36

Q: Determine the area of the shaded region. The value of b is 4 inches. Write the numerical value only.…

A:

Q: Determine the value of the shaded area of the figure shown:

A:

Q: If the horizontal distance was measured to be 130m and the inclination angle was 25 degrees, what is…

A: Considering a line AB having an inclination angle with horizontal of 25 degrees. The horizontal…

Q: The beam is made up of four boards, and is subjected to a moment of M-200 kip in, calculate the…

A:

Q: EXIT 40 F₁ =981NV 6'm 8m Fz 2m F4 De termine magnitude, direction & sense of F2, F3, F4 Fa F3

A:

Q: Calculate Centre of gravity for the following figure + 60 mm 30 mm 2) 80 mm 30 mm 30 mm 100 mm

A: Form the figure there are three sections 1,2,3  Now calculate the area of section 1 A1=60×30A1=1800…

Q: Can you plug in the formula for area show A=

A: Given data  To find the area of the given cross section.

Q: An equilateral triangle of 35 mm side has an edge in the HP which is inclined at 40° to the VP. The…

A: Projections: it is the representation of point, line, or plane surface on the Horizontal and…

Q: 2) USE THE METHOD OF SECTIONS TO FIND THE MAGNITUDE AND DIRECTION OF THE FORCE IN BAR CD SHOWN BELOW…

A:

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.