A Wheatstone bridge strain gage with a gage factor (F) of two is used to monitor axial strain in steel structure of building. The maximum axial strain is expected to be 150 x 10-5. The output voltage of the bridge is connected to an instrumentation amplifier before interfacing it with 5 V analog to digital converter. Design a suitable instrumentation amplifier circuit which allows utilization of the full span of the ADC. V supply 12 V 3 B 200 Ω ww 200 2 200 Ω ww Gage 2 200 Ω Vo VB + Instrum op Amp Vout ADC -Dout

A Wheatstone bridge strain gage with a gage factor (F) of two is used to monitor axial strain in steel structure of building. The maximum axial strain is expected to be 150 x 10-5. The output voltage of the bridge is connected to an instrumentation amplifier before interfacing it with 5 V analog to digital converter. Design a suitable instrumentation amplifier circuit which allows utilization of the full span of the ADC. V supply 12 V 3 B 200 Ω ww 200 2 200 Ω ww Gage 2 200 Ω Vo VB + Instrum op Amp Vout ADC -Dout

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

amplifirs
2. For the following circuit assume r = 8.7 A a. Draw the small signal equivalent circuit. b. Find the input impedance. 16 V 270 2 c. Find output impedance. d. Find the voltage gain. B-110 50 a e. Find the current gain. 2.7 Ti- t
VDD VDD = 5V Ro RD = 3K R1 = 210K Rin RD R2 = 100K R1 RL = 10K oVo VTN = 0.75 Cc1 KN = 0.9 A = 0 RL Vin (+ R2 Find IDQ VDSQ Small-Signal gm ro Draw small-signal eq. circuit Find Av, Rin, Ro
Q2
Which of the following statement is true? Conjugate matching guarantees the maximum output power regardless of input power. The optimum source impedance for the minimum noise figure can be obtained by conjugate matching condition. O The first stage is the most important to minimize the overall noise figure in cascaded blocks An oscillator cannot be built with a single stage amplifier. None of the above
Draw the schematic of a Boost converter and identify the voltage port and current portf or the boost converter
Express the answer in to two decimal places Show the complete solution
Draw the schematic of the Bridge Circuit containing an SCR where the load voltage waveform is unidirectional.
these Questions from ELECTRONICS LAB ,The name of Experement is Op-Amp Inverting and Noninverting Amplifiers.
4. Derive the voltage gain equation for the single-ended primary-inductance converter (SEPIC) shown. L₁ iLI CI iL2 12 D ▷ C₂ R www Vo
Draw the output waveform on the top of the input waveforms for this circuit, Assume that +Vout(max)= +10V and -Vout(max)= -10V .
92 ۱ ۹:۱ ص Qs= 1107 and Qp= 1041 Qs= 1207 and Qp= 1241 Qs= 1007 and Qp= 1041 Qs= 1107 and Qp= 1141 In the figure shown below we can find output current is equal to.. . if the input voltage is equal to 12 mv 12 kO 12 ka 6 ka No option is correct 10 = 32 uA 10 = 34 uA 10 = 38 uA 10 = 36 uA In the fig. shown below we can find the higher critical frequency due to the input