(a) What minimum force F is needed to lift the piano (mass M) using the pulley apparatus shown in Fig. 4–66? (b) Determine the tension in each section of rope: Fr1, Fr2, Fr3, and Fr4. Assume pulleys are massless and frictionless, and that ropes are massless. FT3 F72 FTI FT4 F FIGURE 4-66 Problem 76. स

(a) What minimum force F is needed to lift the piano (mass M) using the pulley apparatus shown in Fig. 4–66? (b) Determine the tension in each section of rope: Fr1, Fr2, Fr3, and Fr4. Assume pulleys are massless and frictionless, and that ropes are massless. FT3 F72 FTI FT4 F FIGURE 4-66 Problem 76. स

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A 100-N block on a rough 30o-incline is acted upon by a force P as shown causing it to accelerate at 2 m/s2 down the plane. The coefficient of kinetic friction is 0.30. (a) Draw the FBD of the block (b) Find the magnitude of P.
65. A 100-kg streetlight is supported equally by two ropes as shown in Figure 4-43. One T 40 40 e rope pulls up and to the right, 40° above the horizon- tal; the other rope pulls up and to the left, 40° above the horizontal. Find the tension in cach rope. SSM Figure 4-43 Problem 65 000
68P. A 5.00 kg block is pulled along a horizontal frictionless floor by a cord that exerts a force F= 12.ON at an angle 6= 25.0 above the horizontal, as shown in Fig. 5-57. (a) What is the acceleration of the block? (b) The force F is slowly increased. What is its value just before the block is lifted (completely) off the floor? (c) What is the acceleration of the block just before it is lifted (completely) off the floor? %3D 5.00 25.0 kg
Asap
1 kg is found A block of mass m = on an inclined plane that makes an angle 30° with the horizontal. The coefficient of static friction and coef- ficient of kinetic friction between the block and the incline are: µs and uk = 0.5. Take the positive di- rection to be up the inclined plane 0.6 %3D 130° With the block initially at rest, the acceleration of the block is
(3) 3rd signi. pls
An object of mass m is at rest on a rough horizontal plane with a coefficient of static friction ue between the surface and the object. A force F is applied in the direction shown in the figure. The minimum force required for the block to be about to move is: F mg He cos 0 sen 0 Hemg cos 0 + le sen 0 a) F = b) F = Hemg cos 0- sen 0 c) F = Hemg cos 0- He sen 0 d) F
(a) A 1 kg block of wood sits on a 30 degree incline. If an applied force of 10 N causes the block to accelerate up the ramp at 0.5 m/s^2 what is the force of friction between the block and the ramp. [K___/4] A
[ii] Two masses are pulled by a horizontal force To on a frictionless horizontal surface as shown. What is the tension force, T, between my and m₂?1 (b) (m, + m₂)g (c) To (d) To (e). (a) mig m₂ m₁ +m₂ m₂ -To (f) my m₁ -To m₂ + m₂ (g) none of the listed
A force is applied to two blocks connected by a massless cable as shown. The coefficients of friction between the blocks and the surface are given (and are different) 45 N 35° 5 kg 10 kg Hk = .3 Hk =.1 Draw the free body diagrams for each block. Decompose all forces into the direction of motion and a perpendicular direction. Calculate all forces except the tension. a.
Three forces acting on an object are given by (-1.95i + 5.70) N, , (s.30l-1.75) N, and , (-49.5) N. The object experiences an acceleration of magnitude 3.60 mys (a) What is the direction of the acceleration? * (counterclockwiise from the +x-axis) (b) What is the mass of the object? kg (c) If the object is initially at rest, what is its speed after 11.0 s? m/s (d) What are the velocity components of the object after 11.0 s? (Let the velocity be denoted by v.) 1) mis I+ Need Help? Weh
3-7. The man attempts to pull down the tree using the cable and small pulley arrangement shown. If the tension in AB is 60 lb, determine the tension in cable CAD and the angle which the cable makes at the pulley. D 20 8 30⁰