A well-insulated tank contains a liquid-vapor mixture of water with quality of 0.4 at 275 kPa. A paddle wheel stirs the mixture until the pressure is 1.0O MPa. By neglecting the change of kinetic and potential energies, determine the work transfer during this process, in kJ/kg.

A well-insulated tank contains a liquid-vapor mixture of water with quality of 0.4 at 275 kPa. A paddle wheel stirs the mixture until the pressure is 1.0O MPa. By neglecting the change of kinetic and potential energies, determine the work transfer during this process, in kJ/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A piston-cylinder device initially contains 3 kg of Refrigerant-134a at 10°C and 600 kPa. At this state, a linear spring (F~x) is touching the piston but exerts no force on it. Heat is now slowly transferred to the refrigerant, causing the pressure rise to 1000 kPa with a volume of 0.03 m2 respectively. ( Required: Determine the following: a) The phases of refrigerant at the initial and final states. b) The final temperature. c) The work in the process. d) Show the process on a P-v diagram with respect to saturation lines
A- One kg of steam with a quality of 21% is heated at a constant pressure of 201 kPa. The work done by the steam is 265 kJ. Calculate the work change of the steam.
CPP 1.5A piston-cylinder device, with a set of stops on the top, initially contains 3kg of air at 200kPa and 27°C. Heat is now transferred to the air, and the piston rises until it hits the stops, at which point the volume is twice the initial volume. More heat is transferred until the pressure inside the cylinder also doubles. Determine: P 1.5.1 the work done; 1.5.2 the amount of heat transfer for this process. 1.5.3 Explain step-by-step the process from the moment that the heat is transferred to the air. m= 3kg P₁ = 200k pa 1773 = 300k
Four pounds of steam initially dry and saturated expand isentropically in a non-flow process from an initial pressure of 275 psia to a final pressure of 125 psia. Find its quality and determine the work done in BTU/lb.
A piston-cylinder device initially contains CO2 at 200 kPa and 400°C and the total enclosed volume is 300 litres. Due to heat loss, the piston moves downwards to a position where it sits on a pair of stoppers and its final enclosed volume is 150 litres. Further heat loss leads to the pressure being reduced to 160kPa. Workout 1) the final temperature, 2) the total work done by CO2 and 3) the total heat transferred to CO2. Also make some comments on the result of heat and create a schematic p-v diagram of the process. The following assumptions are to be made: CO2 is a perfect gas and its molecular mass is 44kg/kmol. The ratio of specific heat capacities, γ (gamma) is 1.3 The volume occupied by the stoppers is to be ignored. There is no leakage in the system There is no friction between the cylinder and piston walls and the piston moved slowly at the same speed therefore, no acceleration. For the conversion from Celsius to Kelvin, use 273 Use 8314.5 J/kmol.K for the universal gas…
thermodynamics
Water at 2.5 MPa and 200°C is heated at constant temperature up to a quality of 80%. (Please include the h-s and T-s diagram in the solution) Find the work of a nonflow process in kJ/kg. Find the quantity of heat received by the water in kJ/kg.Please do not round off intermediate answers, only the final answer in three decimal places.
A mass of 5.1 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder at 100 kPa. Initially, 2.9 kg of the water is in the liquid phase and the rest is in the vapor phase. Heat is now transferred to the water, and the piston, which is resting on a set of stops, starts moving when the pressure inside reaches 300 kPa. Heat transfer continues until the total volume increases by 22 percent. Determine:a) the initial temperature (oC),b) the final temperature (oC),c) the specific volume of water when the piston first starts moving (m3/kg), andd) the work done during this process (kJ). T1 (oC) Format : 98.57 T3 (oC) Format : 320.2 v2 (m3/kg) Format : 0.5376 Wb (kJ) Format : 684.8