A well-insulated rigid tank contains 3 lbm of a saturated liquid–vapor mixture of water at 35 psia. Initially, three-quarters of the mass is in the liquid phase. An electric resistance heater placed in the tank is turned on and kept on until all the liquid in the tank is vaporized. Assume the surroundings to be at 75°F and 14.7 psia. Determine the exergy destruction. Use steam tables. (You must provide an answer before moving on to the next part.) The exergy destruction is _____Btu

Q: Two rigid tanks are connected by a valve. The left tank is filled with 8.6 ft of air initially at 22…

A: Given Pressure, PA = 22 psia               PB = 17.3 psia Volume, VA = 8.6 ft3               VB =…

Q: Helium gas (C,=5.19 kJ/kgK, k=1.67) is compressed steadily from 100 kPa and 30°C to 600 kPa at a…

A: The given values are - P1= 100kPa, T1 =30°C =303 K, P2= 600kPaη=0.6 , k=1.67 , Cp=5.19 kJkgKFor an…

Q: Devices can be combined to perform a variety of tasks. An adiabatic compressor, with air as the…

A: To find: The magnitude of power delivered to generator by turbine. Given: The temperature of the…

Q: A well-insulated 3-m 3 4-m 3 6-m room initially at 7°C is heated by the radiator of a steam- heating…

A: To find Determine the average temperature of the air after in 45 min.GivenThe volume of the room,…

Q: Wet steam at 200oC and 20% moisture is compressed in an irreversible adiabatic process to a pressure…

A:

Q: An insulated rigid tank contains 5kg of air (an ideal gas) at 25C and 100kPa. A paddle wheel inside…

A:

Q: A four -cylinder Carnot engine having a 90 x 120-mm bore and stroke operates between 420 deg C and…

A: SOLUTION FOR 1ST QUESTION GIVEN DATA BORE D=90mm STROKE L=120mm HIGHER TEMPRATURE =420'C LOWER…

Q: 14 kg/s of steam (superheated vapor water) enters a SSSF adiabatic compressor at 100 kPa, 150°C,…

A: Given Data: The mass flow rate of steam is, m˙1=14 kg/s. The pressure of superheated steam is,…

Q: A frictionless piston-cylinder device contains a saturated liquid-vapor mixture of water at 400K.…

A: Given that: dQ = 960 kj Tair = 300k Tmixture= 400k WWe need to find entropy change of the…

Q: Steam enters an isentropic turbine at 4 MPa. X percent (by mass) of the steam exits the turbine at…

A:

Q: Exergy Destruction during Expansion of Steam. A piston-cylinder device contains 0.05 kg of steam at…

A: Given   Mass, m = 0.05 kg   Heat, Q = 2 kJ           T1 = 300 K Find   Exergy destroyed, x…

Q: 5.1) There is an adiabatic turbine to which water vapor enters at 6 MPa with a temperature of 500…

A: Pressure at turbine inlet, P1=6 MPaTemperature at turbine inlet, T1=500oCPressure at turbine outlet,…

Q: An engineer has designed a steam turbine that has to satisfy at least 85% isentropic efficiency. The…

A: At entry :-4MPa,400° CAt exit:-100kpa, 100° C

Q: 0.05 kg low-pressure steam enters the turbine at 1 MPa and 300°C exits at 200 kPa and 150°C. Massive…

A: Note: only 3 subpart is allowed ask in next session please. (a) To find: The exergy of the steam at…

Q: 3. Consider a well-insulated horizontal rigid cylinder that is divided into two compartments by a…

A: The molecules in an ideal gas doesn't interact with each and they continuously undergo collisions…

Q: Refrigerant-22 absorbs heat from a cooled space at 50°F as it flows through an evaporator of a…

A: Given data as per question

Q: Steam enters an isentropic turbine at 4 MPa. X percent (by mass) of the steam exits the turbine at…

A:

Q: m = 1 lbmol/hr T₁ = 1000 °R m = 1 lbmol/hr p₂=2.72 atm W W T₂ = 1000 °R Q = 3000 Btu/hr P₁ = 1 atm m…

A: To check: The statement. Given: The machine is shown below.

Q: -Calculate the quality of 2 kg of saturated steam at P=70 KPa, 2 m A-1 B-0 C- 0.92 D- 0.42 F-0.53…

A: 14.-Here we need to find Quality of saturated steam. 15-Here we need to find Work done

Q: A steam coil (used for heating) has a volume of 20 L and is filled with steam at 200 kPa and 250 °…

A:

Q: An insulated tank is divided into two parts by a partition. One part of the tank contains 3.5 kg of…

A: Mass of fluid = 3.5 kgTemperature of water =  60°CPressure of water = 600 kpaFinal pressure = 10…

Q: 652) A piston-cylinder contains 500 g of R-134a at 1200 kPa and 80 °C. A resistance heater within…

A:

Q: In a piston-cylinder system, there is 3 kg of refrigerant-134a initially at 1.2 MPa and 50°C. The…

A: The mass of refrigerant is .The initial pressure of refrigerant is .The initial temperature of the…

Q: 1. At 3MPa and 400C, 2 kg/s steam flows into a turbine. It exits at 300kPa. The turbine has an…

A:

Q: Refrigerant 134a was added into the repaired compressor. Subsequently, the inlet of the compressor…

A: Given data, Inlet condition of refrigerant (State 1):- Pressure = 0.1 MPa, Temperature = 30 °C Exit…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: as at 500 kPa and 80°C while the other side contains 1 m³ of Helium gas at 500 Pa and 25°C. Now…

A:

Q: Describe the isentropic process involves no irreversibilities and serves as the ideal process for…

A: In the study of thermodynamics, the word isentropic process is an idealized thermal process that is…

Q: Q3 Consider a well-insulated horizontal rigid cylinder that is divided into two compartments by a…

A: For N2:V=1 m3P=500 kPaT=800C=80+273=353 KR=0.2968 kPa.m3/kg.KCV=0.743 kJ/kg0CFor He:V=1 m3P=500…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: It is proposed to have carbon dioxide (CO2) gas pass through an uninsulated nozzle. The CO2 is to…

A:

Q: Oxygen gas is compressed in a piston–cylinder device from an initial state of 12 ft3 /lbm and 75°F…

A: Given data: The characteristic gas constant for oxygen is The specific heat at constant volume for…

Q: Three kilograms of water in a piston-cylinder assembly, initially at 100 kPa and 75°C, are heated at…

A: we know thatPV=mRTfor state 1,substitute 100kpa for P,m=3R=461.89j/k…

Q: Air is compressed by an adiabatic compressor from 95 kPa and 27°C to 600 kPa and 277°C. Assume…

A: We have to find isentropic efficiency of the compressor

Q: Consider a heat engine consisting of two cylinders. Fuel is burned externally to warm one of the two…

A: Given Maximum and minimum temperature is T2 and T1 respectively Molar heat capacity Cv=32R Cycle…

Q: Determine the non-flow exergy of 2.5-kg of steam at 800 kPa and 300 °C, assuming TO = 20°C and PO =…

A: Given Mass of steam = 2.5 kg Temperature = 300 °C , Pressure = 800 kPa T0 = 20 °C and P0 = 100 kPa…