A water piping system is 3000 ft of NPS 20-inch pipe that has three gate valves, one globe valve, one lift check valve, and two standard tees through the flow. Calculate the total pipe length that will include all the straight pipe and valves and fittings. Calculate the pressure drop due to friction if the average flow rate is assumed to be 6.7 ft3/s. Take the value of the Darcy friction factor from Prob (1).

Q: asoline at 77°F flows from a pressurized upper tank to a vented lower tank as shown in the figure…

A: Givenh2=52.8ftTemp=77°Fρgasoline=45lb/ft3

Q: Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4…

A:

Q: Calculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40…

A:

Q: Water (specific gravity, G, is 1.0 and the kinematic viscosity, ν, is 1.14 *10-6 m2 /s) flows…

A: Piping systems may consist of different valves, tees, and elbows, etc. These fittings have their…

Q: A machined entrance cone venture tube that has been fabricated according to ASME standards is fit to…

A:

Q: The diameters D & d piped, Venturi- meter like horizontal water flow sistem seen in the drawing is…

A:

Q: 82 ft of cast iron pipe of 1.5-nominal diameter. All fittings are d regular. Determine the flow rate…

A: given: diameter d=1.5ft height h=23ft

Q: Compute the resulting pressure in kPa after a "real" diffuser in which the energy loss due to sudden…

A:

Q: Compute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K…

A: Given: The diameter of the pipe, d = 3/4 in The volume flow rate, Q = 0.5 gal/min The temperature of…

Q: Calculate the pressure drop across a fully open angle valve placed in 5-in Scheduled 40 steel pipe…

A: To find: The pressure drop across a fully open angle valve. Given: The rate of heat transfer Q=847…

Q: In Figure below, the pipe entrance is sharp-edged having K1 = 0.5, and for the open globe valve…

A: Given that, K1=0.5K2=6Flow rate of water, Q=0.015 m3/sec,Density of water, ρ=1000 kg/m3Friction…

Q: he flow rate of water at 20°C in the center of a pipe with an inside diameter of 102.3mm is measured…

A: Given    Coefficient for the pitot tube = 0.95                                 Height, h = 80 mm…

Q: Find the loss in total pressure for each run in the simple duct system of Fig. 1, using the…

A:

Q: Calculate the flow through a three-new steel pipes connected in series having diameters of 6 in., 8…

A: Given data: The diameter of pipe 1, d1 = 6 in. The diameter of pipe 2, d2 = 8 in. The diameter of…

Q: Water flows through a reducer in a pipe as shown. The pressure at A is equal to 345 kPa and the…

A: GIVEN DATA - PA=345KPa    dA=150mm PB=325KPa    dB=60mm WE HAVE TO CALCULATE FLOW RATE

Q: 20 oC water must be pumped from A to B which has both atmospheric pressure and B is 6 meters above…

A: Given:Water  temperature, T=20°CElevation difference between A  and  B, zB-zA=6mPipe length,…

Q: A series of commercial steel pipe which length, I = 20 in. and diameter, d = 0.8 in. is placed on…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Find the air flow rate in the duct. Data: Air pressure: 17 psia air temperature at the inlet: 65 F…

A: An air channel warmer has various warming components that are either curls or cylinders that are…

Q: Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4…

A: Given:Length of pipe, L=1500 ft =457.2 mVolume flow rate, Q=4 ft3/s =0.113267 m3/sdiameter, d=8 in…

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: Given-Data:- To-Find:- Power (W)=?

Q: Water in an open tank is being pumped to a second tank with a flowrate and viscosity of 0.0624 lb…

A: Water flow rate, m=0.0624 lb/sWater viscosity, μ=6.72*10-4 lb/ft.sSuction side pipe, = 2 in,…

Q: Problem 5 Water is flown at a constant rate through a circular pipe divided into three sections by…

A: The pressure head difference between A and B, ∆h=33 cm=0.33 mPipe diameter, d=150 mm=0.150 mThe flow…

Q: Water at 60F is flowing through a 3-inch inside diameter smooth horizontal pipe. If the Reynolds…

A:

Q: Water at 20°C is being pumped from tank 1 to tank 2 with given conditions. Calculate the power of…

A: Temperature of water, T=20oC Volume flow rate, Q=10 L/s=10*10-3 m3/s=0.01 m3/s Level of tank 1,…

Q: A 6-nominal schedule 80 cast iron pipe is 3500 m long. It is to convey octane at a flow rate of 0.02…

A:

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: The power required by the pump can be calculated using the formula given below- P=ρgQhm where, g is…

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: Given  Rate of flow of water = 7L/s 5in schedule 40 steel pipe. 2 fittings of 90o ell standard long…

Q: Calculate the power supplied to the pump shown if its efficiency is 75%. Water is at 25 degrees…

A:

Q: The piping system shown in the figure is to move ethylene glycol at a flow rate of 50 gpm. Follow…

A: Requirement Pump Head =Friction Pressure drop + losses due to fittings and Valves +Gravity head…

Q: Calculate the minimal head of the pump required to pump 1 m³ of water per second to the height 10 m…

A: Minimum head is the suction head required in centrifugal pump which avoids cavitation in pump…

Q: diameterfor a length of 150m and the remaining 210m is 450mm in diameter.The difference in water…

A:

Q: in a given setup, distilled water at 75 degree f has been found to be transported through a one and…

A:

Q: A pitot tube with dia of 3cm is installed in a pipe with ID150 mm. Water flows through the pipe, and…

A:

Q: determine total head loss of the system and gauge pressure p2 in order to deliver water at 2…

A: For solution refer below images.

Q: Water is pumped through 750 ft of 6-inch nominal diameter Schedule number 40 pipe. The difference in…

A:

Q: 10.86 An air-conditioning system is designed to have a duct with a rectangular cross section 1 ft by…

A: Given Data  For the same pressure drop along the pipe ∆hrect=∆htrap (hf)rect=(hf)trap Hydraulic…

Q: fire -5 m² Figure shows a portion of a protection system in which a pump draws water at 60°F (v…

A: Given data: Q=1500 gal/min=3.34 ft3/sd=10 in Need to determine the required height "h" of the water…

Q: Which of the following equations below describes the system head of the piping shown below. The…

A:

Q: Specifications: The total length of pipe in the three inch branch is 10 ft, and the length of pipe…

A: 1. a. 0.0146 cubm/sb. 0.0012 cubm/s2. 6.67 m3. R = 26806Explanation:Since the pipe having Heat…

Q: PROBLEM 4: a. Compute the flow rate of 20 °C air through a 0.35 m square edged orifice plate that is…

A:

Q: ater is being discharged from a very large reservoir via the piping system shown below. piping…

A:

Q: he diagram shown illustrates the flow in a circular metal duct 20 feet long. The duct has a sudden…

A: According to the above given diagramWe can calculateD=A2π/4D=π/4102×0.6π/4D=7.74 inNow we…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.