A W18 x 86 beam is riveted to a W24 x 117 girder by a connection as shown. The diameter of the rivets is 7/8 in., and the angles are each 4 x 31/2 x 3/8 in. For each rivet, assume that the allowable stresses are T = 15 ksi and o, = 32 ksi. Find the allowable load (kips) on the connection. Relevant data from the table (Appendix B of textbook): shapes): U.S. Customary Units Properties of Wide-Flange Sections (W Designation wi8 x 86 W24 x 117 Web thickness 0.480 in 0.550 in Beam Girder

A W18 x 86 beam is riveted to a W24 x 117 girder by a connection as shown. The diameter of the rivets is 7/8 in., and the angles are each 4 x 31/2 x 3/8 in. For each rivet, assume that the allowable stresses are T = 15 ksi and o, = 32 ksi. Find the allowable load (kips) on the connection. Relevant data from the table (Appendix B of textbook): shapes): U.S. Customary Units Properties of Wide-Flange Sections (W Designation wi8 x 86 W24 x 117 Web thickness 0.480 in 0.550 in Beam Girder

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Calculate the internal forces in the bar GF and GD in a roof truss as shown below. For each bar, indicate if the internal force is tensile or compressive. Use the section method (snittmetoden). Point A has simple support and D has roller support.
SOLVE THIS PROBLEM USING THE SLOPE DEFLECTION EQUATIONS: The bearing type connection show is bolted by 4 – 22 mm diameter bolts (high strength bolts). The size of the plates is 300 mm x 12 mm. Fy 248 MPa, Fn = 330 MPa and Fu = 400 MPa. Determine the following: (1) Design strength of the connection based on strength of plates. (2) Design strength of the connection based on shear strength of bolts. =0.65. (3) Design strength of connection based on bearing strength of bolts on the 12 mm plate. =0.75 12 mm P. mm O. O 300 mm 40 80
Using the methods of joints, determine all the zero-force members of the fink roof truss shown in the figure below. Assume all joints are pin connected. 10 2 kN B 5 kN G F D E
ure B 2m2 m C -2 m D 4 m 500 N 700 N 2 of 2 Part B Identify the zero-force members in the truss shown in (Figure 2). Check all that apply. 000 CD DE CG CF FG BC BG DF AG EF AB Submit Provide Feedback Request Answer
A stud wall panel has an overall height of 4m including top and bottom rails and vertical studs at 400 centres with nogging at mid- height. Assuming that the studs, rail framing and nogging pieces comprise 47 x 125mm section of C24 strength class, calculate the maximum uniformly distributed medium term load the panel is able to support. Use service class condition 2. λιγ = ixx = Scadm.ll (N/mm2) = Choose... • Choose... Choose.... The uniformly distributed load capacity kN/m Choose.... Axxx = K12= Emin/8cl= Choose... • Choose... Choose.... iyy= Choose....
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 24 kips, w = 2.2 kips/ft, LAB = 4.2 ft, LBC = 4.2 ft, and Lcp = 15.8 ft. Determine the magnitude of the maximum bending stress in the beam. P B LAB LBC Answer: Omax tel i |C * ksi W LCD X
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 28 kips, w = 4.6 kips/ft, LAB = 4.6 ft, LBC = 4.6 ft, and LcD = 13.8 ft. Determine the magnitude of the maximum bending stress in the beam. |C D LAB LBC LCD Answer: Omax ksi
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 18 kips, w = 5.6 kips/ft, LAB = 5.0 ft, LBC = 5.0 ft, and LCD = 13.6 ft. Determine the magnitude of the maximum bending stress in the beam. LAB LBC LCD Answer: i ksi Omax
4) The beam shown is under simple tension and has a circular section. What are the normal stresses at the four points (a, b, c and d) of the section shown? F Área transversal-A #F
figure A 2m """" B 2 m C ** 2 m E 4 m D 700 N 500 N 2 of 2 > ▼ Part B Identify the zero-force members in the truss shown in (Figure 2). Check all that apply. EF FG ODF П П П □ DE AB ВС BC AG CG CD BG CF Submit Provide Feedback Request Answer
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P= 23 kips, w = 4.2 kips/ft, LAB = 3.4 ft, LBC = 3.4 ft, and LcD = 15.6 ft. Determine the magnitude of the maximum bending stress in the beam. B |C LAB LBC LCD Answer: Omax = ksi