Please send asap....thank you. Example 2.3a• A voltage supply V=10cos(100t+20°) connected withRL series load, where: R=50 and L=20MH.Determine: 1. current flow in the load2. voltage at resistor3. voltage at inductor

Answered: Image /qna-images/answer/00fac3cb-ba51-441d-b04e-cc8253b96c1c.jpg

Answered: A voltage supply V=10cos(100t+20°)…

A voltage supply V=10cos(100t+20°) connected with RL series load, where: R=5N and L=20mH. Determine: 1. current flow in the load 2. voltage at resistor 3. voltage at inductor

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.8P: Consider the circuit shown in Figure 2.23 in time domain. Convert the entire circuit into phasor...

See similar textbooks

Related questions

Q: 5.) Find the relation between error constants (Kp, Kv, Ka) and steady state error (e,). Find error…

Q: What is a "threshold drop"? In what situations and how does it occur? Describe each situation in the…

A: Threshold drop is the phenomena that generally occurs in Field Effect Transistor.

Q: Draw and Explain the Block Diagram of Superheterodyne AM receiver

Concept explainers

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors. The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.

Question

Please send asap....thank you.

Example 2.3a
• A voltage supply V=10cos(100t+20°) connected with
RL series load, where: R=50 and L=20MH.
Determine: 1. current flow in the load
2. voltage at resistor
3. voltage at inductor

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Figure 2 shows three "LC" circuits, two of them with capacitance capacitors "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitance capacitors "Cc". The currents that circulate through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = −dQ / dt, find the system of coupled equations of the system and then find the normal angular frequencies of the system.
What is this?
A generator rated at 30MVA, 11kV has a reactance of 40%. Calculate its p.u. reactances for a base of 50MVA and 10kV. O 0.606 p.u. O 0.506 p.u. O 0.806 p.u. O 0.706 p.u.
In the circuit in Figure 2, the capacitor andThe circuit of resistance is defined as a load circuit.a) Find the average power dissipated by the load circuit?b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Interpreting the results obtained?c) In the circuit in Figure 2, with a resistance of 80 ohms 23?A coil of is connected in series. In this case,calculating transformer ratio () to optimize power delivery to the load? Obtainedinterpreting the result?d) Calculate the distributed load complex power and reactive power in the newly learned circuit?
aloulated m O1 the value you Up = A cos wt +1o Calaulate maarli)-min(i) =? Use constant voltage drop mad. Don7 to write units. . - 3.7V forget
a. Using Ohm’s Law, compute the voltage and current for eachcomponent. Use the formula Z = Vt / It. b. Compute and record the magnitude and phase angle of the impedanceusing the equation Z= R + RL + jXL – JXC. Use 3uF for the value of C,1.006H for the value of L and for the resistance is computed based onthe specification of the lamp. c. Compute and record for the total power using the formula: Pcomputed = Scosθ d. Compute and record the reactive power and apparent power using theformula Scomputed = V2/ZQcomputed = √S2 − P2 e. Compute for the reactive power (measure) and apparent power(measured) using the formula.Q = PtanθS = P/ cos θ f. Compute the percent difference between the measure and the computedvalue of the impedance.
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
2.)What is the difference between Ampere's law and Biot-Savart's law?
Okay for Determine the mathematical expression for the voltage vC and the current iC for the discharge phase. I got Vc = 8e-t/0.2s V and iC = -4e-t/0.2mA But I need help with the last question Plot the waveforms of vC and iC for a period of time extending from 0to 2 s from when the switch was thrown into position 1.
Q2) Non – sinusoidal voltage applied on 102 resistance with consumed power 521.25 watts and the current is i(t) =10sinwt+I3 sin3wt+0.5 sin5wt Amp. Find the Iz and the voltage effective value.
•A system consists of ,The electric potential opplied to this cell droes o cubie cell, to 1oV from 30OV in one step. •Whot is the hork done? •Whot wald the work done be if it hernt from 3or to 20v and then to lov?
How temperature effect conductivity? Explain with the help of following equation. m e'n7'