A voice signal is bandlimited by an anti-aliasing filter to 3.4 kHz before being (b) linearly quantised and converted into a PCM (Pulse Code Modulation) signal. () What is the function and effect of the anti-aliasing filter? (ii) What would be a suitable minimum sampling rate? (iii) What is the minimum PCM bit rate required to achieve a signal to quantisation noise ratio of greater than 55 dB? (iv) Assuming a raised cosine channel is used for transmission of the PCM signal, with a roll-off factor of 0.32, determine the required channel bandwidth.

A voice signal is bandlimited by an anti-aliasing filter to 3.4 kHz before being (b) linearly quantised and converted into a PCM (Pulse Code Modulation) signal. () What is the function and effect of the anti-aliasing filter? (ii) What would be a suitable minimum sampling rate? (iii) What is the minimum PCM bit rate required to achieve a signal to quantisation noise ratio of greater than 55 dB? (iv) Assuming a raised cosine channel is used for transmission of the PCM signal, with a roll-off factor of 0.32, determine the required channel bandwidth.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the analog signal Description (optional) Image t... x(t) = 3cos100 t (a) Find the minimum sampling rate required to avoid aliasing. Long-answer text (b) If Fs=200 Hz, What is the discrete-time signal after sampling? Long-answer text (c) If Fs=75 Hz, What is the discrete-time signal after sampling?
Given a low level AM modulator with a modulation index of m=0.8 a quiescent voltage gain A=100 an input carrier frequency fc=500Khz with an amplitude Vc=5mV and a 1000 Hz modulating signal. determine:a. Maximum and minimum voltage gainsb. Maximum and minimum amplitudes for Voutc. Sketch the AM output envelope.
(Subject name is "Signal and system") Determine the Nyquist sampling frequency of square wave pulse with width of 2πs.
AF ADM system is designed to operate at 3 times the Nyquist rate for a signal with a 3 kHz bandwidth. The quantizing step size is 250 mV. *** (i) Determine the maximum amplitude of a 1-kHz input siinusoid for which the delta modulator does not show slope overload. (ii) Determine the posfiltered output part (i) signal-to-quantizing-noise ratio for the signal of
Given a low level AM modulator with a modulation index of m=0.8 a quiescent voltage gain A=100 an input carrier frequency fc=500Khz with an amplitude Vc=5mV and a 1000Hz modulating signal determine: a. Maximum and minimum voltage gains b. Maximum and minimum amplitudes for Vout
2/ Information in an analog waveform, whose maximum frequency is 10 kHz, will be transmitted using a minimum sampling rate and a 32-PAM system. transmitted using a minimum sampling frequency and a 32-PAM system. The quantization distortion shall not exceed 0.01% of the The quantization distortion must not exceed 0.01% of the peak-to-peak value of the analog signal. a/ What is the minimum PCM word size to be used in the system? b/ What is the baud rate?
Draw the spectrum of the sampled signal when the sampling rate is equal to 2.5 × 10* d) Draw the spectrum of the sampled signal when the sampling rate is equal to 1× 104 Draw the spectrum of the sampled signal at the Nyquist rte. An analog signal given by: x() = stn'(104) %3D is sampled using an ideal sampling tchnique. a) What is the Nyquist rate of this signal. Samplesec. the samplekse,
What is a minimum number of sampling frequency required to have distortion free reconstruction of a digital signal from its samples?
7. Why does PTM require a higher sampling frequency than PAM? a. The amplitude of PTM signals is constant. b. There are more sidebands in the first replica of a PTM c. Signal than in a PAM signal. d. A sample/hold circuit requires a higher sampling frequency. e. There are fewer sidebands in the first replica of a PTM signal f. Than in a PAM signal.
Explain the effect of the sampling pulse width on the output sampled signal. How can one obtain ideal sampling?
A Delta modulator is used to encode a speech signal x(t) = b sin Wmt band-limited to fm = 10KHz with sampling frequency, fs-100 KHz. For b = +4-volt peak signal voltage, 1) Find the minimum step size to avoid slope overloading. 2) Calculate Signal to quantization noise ratio.