A very large tank contains air at 102 kPa at a location where the atmospheric air is at 100 kPa and 20°C. Now a 2-cm-diameter tap is opened. Determine the maximum flow rate of air through the hole. What would your response be if air is discharged through a 2-m-long, 4-cm-diameter tube with a 2-cm-diameter nozzle? Would you solve the problem the same way if the pressure in the storage tank were 300 kPa?

Q: The calculated shaft work needed to pump water at 20°C is W = -2,545 J/kg at a volumetric flow rate…

A: Given data  shaft work (W) = -2545 J/kg volumetric flow rate (Q) = 0.48 m3/min pump efficiency (n) =…

Q: Butane gas at 300K and 400 kPa enters a 150-mm steel pipe at a velocity of 60 m/s. Assuming…

A: given; pressure (P)=400kpatemperature(T)=300kdiameter(d)=150mm…

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

A: Given, Nozzle inlet: Nozzle outlet:

Q: Saturated liquid refrigerant 134a at 900 kPa is throttled to a pressure of 200 kPa. What is the…

A:

Q: Air is flowing in a wind tunnel at 25°C, 95 kPa, and 250 m/s. The stagnation pressure at the…

A: Given: The temperature of the air in the wind tunnel is T1=25 °C. The pressure of the air in the…

Q: Steam at 0.7Mpa and 250'c expands in a nozzle to 0.1Mpa. Determine the throat and nozzle exit cross…

A:

Q: What is the difference between Inlet velocity and superficial velocity?

A: given: What is the difference between Inlet velocity and superficial velocity?

Q: Glycerin at 40° C with p = 1252 kg/m³ and u = 0.27 kg/m.s is flowing through a 8-cm diameter…

A: Given dataGlycerin at a temp=40°Cwith density=1252 kg/m3μ=0.27 kg/msdiameter d=8 cmflow velocity=3.0…

Q: The compressor tank that holds 80L of air during compression of pressure of 250kpa and the…

A: The gas which follows PV=mRT equation is known as Ideal Gas Equation. There are two conditions which…

Q: In a fixed-geometry wind tunnel, air is drawn in by means of a fan. In the supply reservoir, the…

A:

Q: A vapor enters a group of convergent-divergent nozzles at 3 MPa and 300 oC and expands to 0.5 MPa.…

A:

Q: A pump is being used to transport a liquid food product (ρ = 1250 kg/m3, μ = 1.5 cP) from a holding…

A:

Q: A pipe carrying water has an inlet of diameter 0.18 m and an outlet which is 1.11 m below the inlet…

A:

Q: The 64-W fan in an aircraft environmental system is to circulate air through the ducting. An…

A: As fluid flow takes place across fan, it is treated as open system and hence control volume approach…

Q: Water at the initial pressure of 1 atm and temperature of 15C is flowing through a pump. Final…

A:

Q: (a) A storage tank is connected to a piping system as illustrated in Figure P1. Water at temperature…

A: Major and minor losses are the most common types of energy losses in fluid flow across a pipe…

Q: What is the mathematical model of enthalpy? What is the mathematical model to calculate the flow…

A: The oxidation reaction in the gas area is represented by the system of nonstationary partial…

Q: The flow inside a pipe after the velocity profile fully develops is:

A: To Find The flow inside a pipe after the velocity profile fully develops is:

Q: Air flows through a nozzle from a large vessel in which the pressure and temperature are 500 kPa and…

A:

Q: Air is flowing through a venturi meter whose diameter is 2.6 in at the entrance part (location 1)…

A:

Q: Helium at 14.7 psia is compressed at a constant temperature of and 68 degrees Fahrenheit. Calculate…

A:

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

A:

Q: Air is flowing through a venture-meter whose diameter is 2.6 in at the entrance part (location 1)…

A:

Q: horizontal convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed…

A:

Q: In a boiler of a steam power plant the incoming water is heated to steam by hot gas flowing around…

A:

Q: • Air enters a very large compressor at a rate of 4.5 m3/s. The inlet conditions are 100 kPa and 27…

A:

Q: Knowing the density, P and the volumetric flow rate, the mass flow rate, mdot can be calculate using…

A: Given: Density = ρVolumetric flow rate = ϑ Let, mdot=mass flow rate

Q: Air is compressed polytropically from 101 Kpa and 23 °C and delivered to a tank at 1500 kpa and 175…

A:

Q: The cooling system given in the figure is fed with water at a flow rate of 15 g /s and a temperature…

A: Given: T1 = 80°C m˙ = 15 g/s V = 300 cm3 Q = 500 cal/s

Q: Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to…

A:

Q: The thrust developed by the engine of a Boeing 777 is about 380 kN. Assuming choked flow in the…

A: Given: The thrust developed by the engine is F=380 kN. The ambient temperature is T=215 K. The…

Q: Prove this equation for the frictional adiabatic process in a fixed cross-section duct.(Dont…

A:

Q: ygen flows into a tube of 10cm diameter at 0.25kg/s, under 4.5atm pressure and 25°C temperature. It…

A: Given:d1=10 cmm=0.25 kg/sP1=4.5 atmT1=25°CP2=2.5 atm

Q: Steam exits a turbine and enters a 1.435-m- diameter duct. The steam is at 4.5 kPa and has a quality…

A: Given Data: The diameter at the turbine exit is, D=1.435 m. The pressure of steam at exit is, P=4.5…

Q: Air at temperature 26 °C and pressure 101.4 kPa enters the diffuser steadily with a velocity of 190…

A:

Q: Air flows steadily and isentroplcally into an aircraft inlet at a rnass flow rate of 100 kgs·1• At a…

A: Given data: The mass flow rate is m˙=100 kg/s The area at the inlet is A1=0.5 m2 The inlet…

Q: The water vapor is throttled by an insulated valve from 6 MPa pressure and 400oC temperature to 2…

A: